Arctic Cat HDX CREW 2017 Скачать руководство пользователя страница 79

Страница: 79 / 152

16. Place the V-belt cover gasket into position; then

install the cover and secure with the cap screws with

fibrous washers making sure the different-lengthed

cap screws are in their proper location. Tighten the

cap screws to 44 in.-lb.

H1-017

Center Crankcase

Components



NOTE: This procedure cannot be done with the

engine/transmission in the frame. Complete Remov-

ing procedures for Top-Side, Left-Side, and Right-

Side must precede this procedure.

Separating Crankcase

Halves

1. Remove the right-side cap screws securing the

crankcase halves. Note the location of the different-

lengthed cap screws.

2. Remove the left-side cap screws securing the crank-

case halves. Note the location of the different-

lengthed cap screws.

3. Using the Crankcase Separator/Crankshaft Remover

and tapping lightly with a rubber mallet, separate the

crankcase halves. Account for two alignment pins.



NOTE: To keep the shaft/gear assemblies intact for

identification, tap the shafts toward the left-side

crankcase half when separating the halves.

PR786

Disassembling Crankcase

Half



NOTE: For steps 1-7, refer to illustration PR787A.



NOTE: To aid in installing, it is recommended that

the assemblies are kept together and IN ORDER.

PR787A

1. Remove the secondary driven shaft assembly (A)

noting the location of the bearing locating pins.

Account for the bearing C-ring.

PR787B

2. Remove the reverse idler gear assembly (F). Account

for all washers, shaft, bushing, and the gear.

CC668

KEY

A. Secondary Driven Shaft

Assembly

B. Crank Balancer Assembly

C. Crankshaft

D. Countershaft Assembly

E. Driveshaft

F. Reverse Idler Gear Assembly

G. Gear Shift Shaft

H. Shift Shaft with 2 Forks

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды