Arctic Cat HDX CREW 2017 Скачать руководство пользователя

Страница: 40 / 152

Engine/Transmission

This section has been organized into sub-sections which

show a progression for the complete servicing of the Arc-

tic Cat ROV engine/transmission.



NOTE: For efficiency, it is preferable to remove and

disassemble only those components which need to be

addressed and to service only those components. The

technician should use discretion and sound judgment.

To service the center crankcase halves, the engine/trans-

mission must be removed from the frame. To service top-

side, left-side, and right-side components, the engine/

transmission does not have to be removed from the

frame.



NOTE: Arctic Cat recommends the use of new gas-

kets, lock nuts, and seals and lubricating all internal

components when servicing the engine/ transmission.



NOTE: A new ROV and an overhauled ROV engine

require a “break-in” period. The first 10 hours (or

200 miles) are most critical to the life of this ROV.

Proper operation during this break-in period will

help assure maximum life and performance from the

ROV. Instruct the customer to follow the proper

break-in procedure as described in the Operators

Manual.

SPECIAL TOOLS

A number of special tools must be available to the techni-

cian when performing service procedures in this section.

Refer to the current Special Tools Catalog for the appro-

priate tool description.



NOTE: When indicated for use, each special tool

will be identified by its specific name, as shown in the

chart below, and capitalized.



NOTE: Special tools are available from the Arctic

Cat Service Department.



AT THIS POINT

To service any one specific component, only limited dis-
assembly of components may be necessary. Note the
AT THIS POINT information in each sub-section.

Description

p/n

Seal Protector Tool

0444-252

Crankcase Separator/Crankshaft Remover

0444-152

Magneto Rotor Remover Set

0444-254

Piston Pin Puller

0644-328

Secondary Drive Gear Holder

0444-253

Spanner Wrench

0444-240

Surface Plate

0644-016

V Blocks

0644-535

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды