Arctic Cat HDX CREW 2017 Скачать руководство пользователя

Страница: 117 / 152

116

Drive System

GENERAL INFORMATION

Gear cases are 3.6:1 ratio.

The die-cast aluminum housings have been assembled

with thread-rolling screws (trilobular). When assembling

with these screws, start the screws carefully into the

housing; then use the following torque values.



NOTE: Never reuse a lock nut. Once a lock nut has

been removed, it must be replaced with a new lock

nut.

SPECIAL TOOLS

A number of special tools must be available to the techni-

cian when performing service procedures in this section.

Refer to the current Special Tools Catalog for the appro-

priate tool description.



NOTE: When indicated for use, each special tool

will be identified by its specific name, as shown in the

chart below, and capitalized.



NOTE: Special tools are available from the Arctic

Cat Service Department.

Front Drive Actuator



NOTE: The actuator is not a serviceable compo-

nent. If it is defective, it must be replaced.



NOTE: The actuator will operate only when the

ignition switch is in the ON position.

The front drive actuator is located on the left side of the

front differential input housing. With the engine stopped

and the ignition switch in the ON position, a momentary

“whirring” sound can be heard each time the drive select

switch is shifted. If no sound is heard, see Electrical Sys-

tem. If the actuator runs constantly or makes squealing or

grinding sounds, the actuator must be replaced.

REMOVING

1. Select LOCK on the drive select switch; then discon-

nect the connector on the actuator harness. Remove

the front six cap screws securing the skid plate to the

frame.

2. Using a T-30 torx wrench, remove the mounting cap

screw from the driveshaft side of the actuator.

WC938A

3. Remove the mounting cap screw from below the

actuator on the suspension side.

HDX376A

4. Loosen but do not remove the mounting cap screw at

the front of the actuator; then slide the actuator to the

rear enough to clear the slotted mounting tab and the

selector shaft. Remove through the bottom of the

frame.

WC939A

INSTALLING

1. Lubricate the O-rings on the actuator; then ensure all

mounting surfaces are clean and free of debris.

2. Align the actuator with the selector shaft and slide it

forward onto the shaft taking care to engage the cap

screw in the slot of the front mounting tab.



NOTE: Make sure to properly align the differential

lock actuator lever with the hole in the differential

lock plunger.

Size

New Housing

Reassembled

Housing

M6 (Torx T-30 Recess)

9 ft-lb

8 ft-lb

M8 (Torx T-40 Recess)

28 ft-lb

23 ft-lb

Description

p/n

Backlash Measuring Tool (24-Spline Axle)

0544-010

Backlash Measuring Tool (27-Spline Axle)

0544-011

CV Boot Clamp Tool

0444-120

Internal Hex Socket

0444-104

Pinion Gear/Shaft Removal Tool

0444-127

Gear Case Seal Installer Tool

0444-273

Hub Retaining Wrench

0444-270

U-Joint Separator Tool

0444-128

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды