Arctic Cat HDX CREW 2017 Скачать руководство пользователя страница 97

Страница: 97 / 152

6. If using the CTEK Multi US 800, there are no further

buttons to push. If using the CTEK Multi US 3300,

press the Mode button (A) at the left of the charger

until the Maintenance Charge Icon (B) at the bottom

illuminates. The Normal Charge Indicator (C) should

illuminate on the upper portion of the battery charger.

800E



NOTE: The maintainer/charger will charge the bat-

tery to 95% capacity at which time the Maintenance

Charge Indicator (D) will illuminate and the main-

tainer/charger will change to pulse/float maintenance.

If the battery falls below 12.9 DC volts, the charger

will automatically start again at the first step of the

charge sequence.

3300A



NOTE: Not using a battery charger with the proper

float maintenance will damage the battery if con-

nected over extended periods.

Charging



NOTE: Arctic Cat recommends the use of the

CTEK Multi US 800 or the CTEK Multi US 3300 for

battery maintenance charging.

1. Be sure the battery and terminals have been cleaned

with a baking soda and water solution.

2. Be sure the charger and battery are in a well-venti-

lated area and ensure the battery charger cables will

not contact any battery acid. Be sure the charger is

unplugged from the 110-volt electrical outlet.

3. Connect the red terminal lead from the charger to the

positive terminal of the battery; then connect the

black terminal lead of the charger to the negative ter-

minal of the battery.

4. Plug the charger into a 110-volt electrical outlet.

5. By pushing the Mode button (A) on the left side of

the charger, select the Normal Charge Icon (E). The

Normal Charge Indicator (C) should illuminate on

the upper left portion of the charger.

6. The battery will charge to 95% of its capacity at

which time the Maintenance Charge Indicator (D)

will illuminate.



NOTE: For optimal charge and performance, leave

the charger connected to the battery for a minimum 1

hour after the Maintenance Charge Indicator (D) illu-

minates. If the battery becomes hot to the touch, stop

charging. Resume after it has cooled.

7. Once the battery has reached full charge, unplug the

charger from the 110-volt electrical outlet.



NOTE: If, after charging, the battery does not perform

to operator expectations, bring the battery to an autho-

rized Arctic Cat dealer for further troubleshooting.

Electronic Power Steering

(EPS)

The EPS system is an electro-mechanical device that uti-

lizes 12 volt DC power to drive a motor linked to the

steering shaft to assist the driver when rotating the steer-

ing wheel. Driver steering inputs are detected by a

torque-sensing transducer assembly within the EPS hous-

ing. These inputs are converted to electronic signals by

the transducer and control circuitry to tell the motor

which way to drive the steering shaft. When no steering

input (pressure on the steering wheel) is detected, no

torque signal is generated, and no steering assist is pro-

vided by the motor.

If an electrical-related EPS system malfunction occurs, a

diagnostic trouble code (DTC) will be displayed on the

LCD gauge. Check for updates and verify any active DTCs

using the most up-to-date CATT II software. The following

is a list of DTCs, possible conditions, and causes.



NOTE: If no active codes are present on the LCD or

verified through CATT II and the vehicle is experi-

encing steering-related issues, there may be a

mechanical steering-related issue. In this case, the

EPS is not the cause of the issue. Components that

may contribute to this type of issue could be abnormal

tire wear, bad wheel bearings, ball joints, tie rod ends,

tie rods, or bushings. Check the complete steering sys-

tem for any sign of wear or misalignment.



NOTE: If any code C1306-C1315 or C1317-C1325

are active and verified with CATT II, EPS replace-

ment is not necessary. Follow the instructions listed in

the chart to correct the malfunction.

Component data and system updates can be retrieved/
performed using the CATT II. Navigate the screens as
required.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды