Arctic Cat HDX CREW 2017 Скачать руководство пользователя

Страница: 8 / 152

Periodic Maintenance/

Tune-Up

Tighten all nuts, bolts, and cap screws. Care must be

taken that all calibrated nuts, bolts, and cap screws are

tightened to specifications.

It is advisable to lubricate certain components periodi-

cally to ensure free movement. Apply light oil to the

components using the following list as reference.

A. Accelerator Pedal Pivot/Cable Ends

B. Brake Pedal Pivot

C. Shift Cable

SPECIAL TOOLS

A number of special tools must be available to the techni-

cian when performing service procedures in this section.

Refer to the current Special Tools Catalog for the appro-

priate tool description.



NOTE: When indicated for use, each special tool

will be identified by its specific name, as shown in the

chart below, and capitalized.



NOTE: Special tools are available from the Arctic

Cat Service Department.

Air Inlet Pre-Filter

This vehicle is equipped with a foam pre-filter to filter

dirt from the inlet air prior to reaching the main air filter.



NOTE: To access the pre-filter, open the cargo box.

1. Gently squeeze the pre-filter cover and lift it up to

expose the pre-filter.

HDX237A

2. Loosen the clamp securing the pre-filter.

HDX235

3. Remove the pre-filter assembly and wash thoroughly

in warm, soapy water; then rinse and dry.

4. Install and secure with the clamp. Tighten securely;

then install the pre-filter cover.

Air Filter



NOTE: To access the air filter, the cargo box must

be raised.

1. Remove dirt and debris from around the filter hous-

ing.

2. Unsnap the four spring-clip fasteners and remove the

air filter cover. Remove the two wing nuts securing

the filter.

3. Place the element in a pan larger than the element

and spray all sides generously with cleaning solvent.

Let sit approximately three minutes.

HDX050A



NOTE: Cleaning Solvent and Aerosol Air Filter Oil

are available from Arctic Cat.

4. In a pan larger than the element, with a mild deter-

gent (dish soap) and water, wash all the dirt and oil

off by squeezing the element. Ringing or twisting the

filter may cause damage.

5. Rinse off any remaining soap.

Description

p/n

Compression Tester Kit

0444-213

Oil Filter Wrench

0644-389

Timing Light

0644-296

Valve Clearance Adjuster

0444-255

CAUTION

Failure to inspect the air filter frequently if the vehicle is
used in dusty, wet, or muddy conditions can damage
the engine.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды