Arctic Cat HDX CREW 2017 Скачать руководство пользователя

Страница: 146 / 152

145

HDX340

3. Place a new circlip into position (A) on the wear

sleeve.

VOR-059A

HDX341

4. Slide the spring retainer up against the circlip; then,

using a punch or flat blade screw driver, seat the cir-

clip into the internal recess of the spring retainer.



NOTE: Place a piece of duct tape around the outside

diameter of the shock body below the wear sleeve to

protect the finish of the shock body.

HDX342

5. Slowly decompress the spring via the shock spring

compressors to remove tension from the spring; then

remove the spring compressor tool.

Front A-Arms

REMOVING

1. Remove the hubs (see Drive System).

2. Remove the brake hose clamp from the upper A-arm;

then release the anchors from the A-arm.

HDX295A

3. Remove the cotter pin and slotted nut securing the tie

rod end to the knuckle; then remove the tie rod end

from the knuckle.

4. Remove the cap screws securing the ball joints to the

knuckle.

CAUTION

Support the knuckle when removing the cap screws or
damage to the threads will occur.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды