Arctic Cat HDX CREW 2017 Скачать руководство пользователя

Страница: 100 / 152

HDX290

2. The meter reading must be less than 1 ohm.



NOTE: Secondary coil resistance checks are not rec-

ommended. An internal diode in the coil prevents

accurate secondary resistance measurements.

Spark Plug Cap

1. Connect the red tester lead to one end of the cap;

then connect the black tester lead to the other end of

the cap.

AR603D

2. The meter must show 4000-6000 ohms.



NOTE: If the meter does not show as specified,

replace the spark plug cap.

Ignition Timing

The ignition timing cannot be adjusted; however, verify-

ing ignition timing can aid in troubleshooting other com-

ponents. To verify ignition timing, use the following

procedure.



NOTE: To check ignition timing, the front seat, seat

back, and seat base must be removed.

1. Attach the Timing Light to the spark plug high ten-

sion lead; then remove the timing inspection plug

from the left-side crankcase cover.

2. Start the engine and using the RPM function on the

speedometer/tachometer, run at 1300 RPM; ignition

timing should be 16° BTDC.

3. Install the timing inspection plug.

If ignition timing cannot be verified, the rotor may be

damaged, the key may be sheared, the trigger coil bracket

may be bent or damaged, or the ECM may be faulty.

Accessory Receptacle/

Connector



NOTE: This test procedure is for either the recepta-

cles or the connectors.

VOLTAGE

1. Turn the ignition switch to the ON position; then set

the meter selector to the DC Voltage position.

2. Connect the red tester lead to the orange/black wire;

then connect the black tester lead to ground.

3. The meter must show battery voltage.



NOTE: If the meter shows no battery voltage, trou-

bleshoot the battery, fuse, receptacle, connector, or

the main wiring harness.

Switches

Seat Belt Limiter Switch
RESISTANCE

1. Remove the front passenger seat. Locate the switch

connector on the driver’s side; then disconnect.

HDX373

2. Buckle the driver’s seat belt. On the switch side, con-

nect one meter lead to one pin and the other meter

lead to the opposite connector pin.

HDX374

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды