Arctic Cat HDX CREW 2017 Скачать руководство пользователя страница 72

Страница: 72 / 152

INSPECTING OIL PUMP

1. Inspect the pump for damage.

2. It is inadvisable to remove the screw securing the

pump halves. If the oil pump is damaged, it must be

replaced.

CC446D

DRIVE CLUTCH ASSEMBLY
Disassembling and Inspecting

1. Slide the sheave plate out of the movable drive

sheave. Make note of each drive face plate damper

orientation before removing. Check for excessive

wear, warping or any cracks. Replace as necessary.

Check the internal splines of the sheave plate for

excessive or abnormal wear. Inspect the roller sur-

face of the sheave plate for abnormal wear or pitting.

Replace as necessary.

CF378

MD1036

2. Note the roller locations; then remove the rollers.

Check for flat spots or abnormal wear. Measure the

outside diameter; standard measurement is 30 mm. If

excessively worn, replace as necessary.

ATV1152A

3. Check the internal bushing of the movable drive

sheave and surface of the spacer. Replace as neces-

sary. Check the fixed drive sheave internal splines

for excessive wear. Check for any broken cooling

fins and replace as necessary.

MD1094

Assembling

1. Install the fixed drive sheave to the centrifugal clutch

housing shaft.

MD1094

2. As noted during disassembling, place each roller into

each valley of the movable drive sheave. With the

dampers installed onto the sheave plate, install the

sheave plate into the movable drive sheave.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды