Arctic Cat HDX CREW 2017 Скачать руководство пользователя страница 24

Страница: 24 / 152

PR961

6. Using the Hub Retaining Wrench, secure the hub

assembly with the nut. Tighten to 200 ft-lb.

PR256

7. Install the retaining plate.



NOTE: If necessary, tighten the hub nut clockwise

to allow the retaining plate to sit flush with the hub.

PR965

8. Secure the brake caliper to the knuckle with the two

new “patch-lock” cap screws. Tighten to 20 ft-lb.

PR377B

9. Install the wheels and using a crisscross pattern,

tighten the wheel nuts in 20 ft-lb increments to a final

torque of 40 ft-lb (steel wheel), 60 ft-lb (aluminum

wheel w/black nuts), or 80 ft-lb (aluminum wheel w/

chrome nuts).

10. Remove the vehicle from the support stand.

Accelerator Pedal

REMOVING

Dislodge the throttle cable holding grommet from the

actuator arm; then remove two torx-head screws and nuts

securing the accelerator pedal assembly to the splash

panel and remove the accelerator pedal.

PR709

HDX309

INSTALLING

Align the mounting holes with the holes in the splash

panel and secure with the two torx-head screws and nuts;

then snap the throttle cable holding grommet into the

actuator arm.

Shift Lever

REMOVING

1. Remove the plastic push-pin from the shift lever

knob; then remove the knob.

2. Remove the cap screw and lock nut securing the shift

lever to the shift cable. Discard the lock nut.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды