Arctic Cat HDX CREW 2017 Скачать руководство пользователя

Страница: 112 / 152

111

2. Battery voltage with engine idling (charging = 13.8

VDC or greater).

3. Battery voltage with electrical accessories operating,

engine idling (13.5 VDC or greater).

4. Battery voltage starter cranking (10.5-11.5 VDC).

Coolant (COOLANT)

WT591

Display: Engine coolant temperature as measured by the

ECT sensor.

DTC: P0116, P0117, P0118, P0119

Usage: Monitor coolant temperature to verify the follow-

ing.

1. ECT sensor signal.

2. High Temperature indicator (on @ 230° F.)

3. Thermostat opening @ approximately 180° F, indi-

cated by a momentary drop or pause in the rising

temperature reading.

4. Fan ON @ 185° F, OFF @ 176° F:

A. fan motor

B. fan relay

C. fan fuse

D. wiring connections

5. High Temperature Rev Limiter 5000 RPM @ 230° F.

Inlet Air Temperature (INTAKE)

WT592

Display: Inlet air temperature in Fahrenheit or Celsius.

DTC: P0112, P0113, P0114

Usage: Verify correct output of IAT sensor.



NOTE: After engine has been running, IAT read-

ings will be higher than outside air temperature due

to engine and engine compartment heat as well as

intake manifold heating.

MAP (AIR PRESS)

WT602

Display: MAP in millibars and in./Hg.

DTC: P0107, P0108

Usage: Verify barometric pressure signal correct.



NOTE: Local barometric pressure is given in in./Hg

(inches of mercury) and millibars. The gauge should

display approximately 965 millibars at 970 ft. above

sea level. This number will not change when the

engine is started. However, the value is being

observed internally in the ECM.

Idle Step Control (ISC)

WT542

Display: ISC position

DTC: P0508, P0509

Usage: Verify correct ISC position.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды