Arctic Cat HDX CREW 2017 Скачать руководство пользователя страница 93

Страница: 93 / 152

RADIATOR
Removing

1. Open the hood and remove the weather strip; then

remove the front access panel, front fenders, and

front storage box.

PR890A

2. Drain the coolant into a suitable container; then dis-

connect the cooling fan wire connector from the

main harness.

PR957

PR912A

3. Remove the two shoulder bolts and nuts securing the

radiator to the frame; then disconnect the upper and

lower coolant hoses. Remove the reservoir tank hose

from the radiator filter neck.

PR184A

4. Remove the screws securing the oiler cooler to the

radiator (two on each side). Place a protective cloth

over the oil cover fins to prevent damage when

removing the radiator.

HDX371A

5. Lift the radiator assembly from the vehicle. Account

for two upper and two lower rubber mounting grom-

mets.

Cleaning and Inspecting

1. Flush the radiator with water to remove any contami-

nants.

2. Inspect the radiator for leaks and damage.

3. Inspect all hoses for cracks and deterioration.

4. Inspect all fasteners and grommets for damage or

wear.

Installing

1. Place the radiator into position making sure the

grommets are correctly installed; then secure to the

mounts with the two shoulder bolts and nuts. Tighten

to 8 ft-lb.

CAUTION

After operating the vehicle for the initial 5-10 minutes,
stop the engine, allow the engine to cool down, and
check the coolant level. Add coolant as necessary.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды