Arctic Cat HDX CREW 2017 Скачать руководство пользователя

Страница: 141 / 152

140

PR338

PR336

4. Remove the master cylinder. Discard the three crush

washers.

Inspecting

1. Inspect the master cylinder push rod and clevis for

wear, bending, or elongation of clevis holes.

2. Inspect the push rod boot for tears or deterioration.

3. Inspect the reservoir for cracks and leakage.

4. Inspect the brake hose for cracks and deterioration

and the condition of the banjo-fittings.

Installing

1. Secure the master cylinder assembly to the frame with

two cap screws and two flange nuts. Tighten to 25 ft-lb.

2. Using new crush washers, secure the banjo-fittings

to the master cylinder with a new banjo bolt and the

existing brake switch. Tighten to 20 ft-lb.

3. Install the pivot pin and secure with a new cotter pin.

4. Fill the master cylinder and bleed the brake system

(see Hydraulic Brake System in the Periodic Mainte-

nance/Tune-Up section).

CAUTION

Brake fluid is highly corrosive. Do not spill brake fluid
on any surface of the vehicle.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды