Arctic Cat HDX CREW 2017 Скачать руководство пользователя

Страница: 65 / 152

3. Inspect the one-way bearing for chipped surfaces,

missing rollers, or discoloration. If any of the above

conditions exist, replace the starter clutch assembly.

FI572

REPLACING STARTER CLUTCH
ASSEMBLY

1. Remove the cap screws securing the starter clutch

assembly to the flywheel; then remove from the fly-

wheel.

FI570

2. Thoroughly clean the rotor/flywheel; then install the

new clutch and secure with the cap screws after

applying a drop of red Loctite #271 to the threads.

Tighten to 26 ft-lb using a crisscross pattern. Make

sure the one-way bearing is installed with the

notches directed away from the rotor/flywheel.

FI576A

FI578

REPLACING STARTER GEAR BEARING

1. Support the starter clutch gear in a press making sure

to support the hub around the entire circumference;

then using a suitable bearing driver, press the bearing

from the gear.

FI583

2. Thoroughly clean the gear hub; then apply a drop of

green Loctite #620 to the bearing outer race and

press into the gear hub until even with the lower

chamfer radius.

FI580

INSPECTING STATOR COIL/MAGNETO
COVER ASSEMBLY

1. Inspect the stator coil for burned or discolored wir-

ing, broken or missing hold-down clips, or loose cap

screws.

2. Inspect the bearings in the magneto housing for dis-

coloration, roughness when rotated, and secure fit in

bearing bores.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды