Arctic Cat HDX CREW 2017 Скачать руководство пользователя

Страница: 127 / 152

126

XR354

7. Install the shift fork assembly making sure the fork

leg is facing upward. Apply a small amount of oil to

the gasket; then install the gasket.

8. Place the input shaft assembly onto the gear case

housing; then secure with the existing cap screws.

Tighten to 23 ft-lb.



NOTE: If a new housing is being installed, tighten

the cap screws to 28 ft-lb.

XR353

XR347

Removing/Installing Axle Seal



NOTE: This procedure can be performed on a rear

gear case.

1. Remove the seal using a seal removal tool.

XR360



NOTE: Prior to installing the seal, apply High-Per-

formance #2 Molybdenum Disulphide grease to the

seal outside diameter.

2. Using Gear Case Seal Installer Tool, evenly press the

seal into the cover bore until properly seated.

CF278

3. Repeat steps 1-2 for the opposite side.

INSTALLING DIFFERENTIAL

1. Liberally apply grease to the propeller shaft splines

using molybdenum grease; then place the differential

assembly into position in the frame engaging the

front propeller shaft.

HDX379

2. At this point, position the rubber coupler between

both propeller shafts; then loosely install six new cap

screws and six new lock nuts.

CAUTION

Make sure the tool is free of nicks or sharp edges or
damage to the seal may occur.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды