Arctic Cat HDX CREW 2017 Скачать руководство пользователя

Страница: 3 / 152

General Information/

Foreword

This Arctic Cat Service Manual contains service, mainte-

nance, and troubleshooting information for the 2017 Arc-

tic Cat HDX Crew. The complete manual is designed to

aid service personnel in service-oriented applications.

This manual is divided into sections. Each section covers

a specific vehicle component or system and, in addition

to the standard service procedures, includes disassem-

bling, inspecting, and assembling instructions. When

using this manual as a guide, the technician should use

discretion as to how much disassembly is needed to cor-

rect any given condition.

This service manual is designed primarily for use by an

Arctic Cat CatMaster Basic Level technician. The proce-

dures found in this manual are of varying difficulty, and

certain service procedures in this manual require one or

more special tools to be completed. The technician

should use sound judgment when determining which pro-

cedures can be completed based on their skill level and

access to appropriate special tools.



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is nec-

essary.

When replacement of parts is necessary, use only genuine

Arctic Cat parts. They are precision-made to ensure high

quality and correct fit. Refer to the appropriate Illustrated

Parts Manual for the correct part number, quantity, and

description.

All Arctic Cat publications and decals display the words

Warning, Caution, Note, and At This Point to emphasize

important information. The symbol

! WARNING

identifies personal safety-related information. Be sure to

follow the directive because it deals with the possibility

of serious personal injury or even death. A

CAU-

TION

identifies unsafe practices which may result in

vehicle-related damage. Follow the directive because it

deals with the possibility of damaging part or parts of the

vehicle. The symbol



NOTE:

identifies supplementary

information worthy of particular attention. The symbol



AT THIS POINT

directs the technician to cer-

tain and specific procedures to promote efficiency and to

improve clarity.

At the time of publication, all information, photographs,

and illustrations were technically correct. Some photo-

graphs used in this manual are used for clarity purposes

only and are not designed to depict actual conditions.

Because Arctic Cat Inc. constantly refines and improves

its products, no retroactive obligation is incurred.

All materials and specifications are subject to change

without notice.

Product Service and

Warranty Department

Arctic Cat Inc.

Specifications



NOTE: Specifications subject to change without notice.

MISCELLANY

Tire Size

(front)

(rear)

26 x 9R-14
26 x 11R-14

Tire Inflation Pressure

110 kPa (16 psi)

Spark Plug Type

NGK CPR8E

Spark Plug Gap

0.5-0.6 mm (0.019-0.024 in.)

Gas Tank Capacity

33 L (8.74 U.S. gal.)

Coolant Capacity

4.5 L (4.76 U.S. qt)

Front Differential Capacity

269 ml (9.1 fl oz)*

Rear Drive Capacity

269 ml (9.1 fl oz)*

Engine Oil Capacity (approx)

2.2 L (2.4 U.S. qt) - Overhaul
1.9 L (2.0 U.S. qt) - Change

Gasoline (recommended)

87 Octane Regular
Unleaded

Engine Oil (recommended)

Arctic Cat ACX All Weather
Synthetic

Front Differential/Rear Drive Lubricant

SAE Approved 80W-90
Hypoid

Drive Belt Width

35.0 mm (1.38 in.)

Brake Fluid

DOT 4

Taillight/Brakelight

12V/8W/27W

Headlight

12V/60/55W

ELECTRICAL SYSTEM

Ignition Timing

16° BTDC @ 1300 RPM

Spark Plug Cap

5000 ohms

Ignition Coil Resistance

(primary)

(secondary)

Less than 1 ohm
N/A

Ignition Coil Primary Voltage

Battery Voltage

Stator Coil Resistance

(CKP Sensor)

(AC generator)

104-156 ohms
Less than 1 ohm

AC Generator Output (no load)

60 AC volts @

5000 RPM

Crankshaft Position Sensor AC Voltage

1.8 volts or more

VALVES AND GUIDES

Valve Face Diameter

(intake)

(exhaust)

31.6 mm
27.9 mm

Valve/Tappet Clearance

(intake)

(cold engine)

(exhaust)

0.1016 mm
0.1524 mm

Valve Guide/Stem Clearance

(max) 0.051 mm (intake)

0.063 mm (exhaust)

Valve Guide Inside Diameter

5.000-5.023 mm

Valve Head Thickness

2.3-2.7 mm (intake)
2.36-2.76 mm (exhaust)

Valve Seat Angle

45° +15’/+30’

Valve Spring Free Length

(min) 38.65 mm

Valve Spring Tension @ 31.5 mm

16.32 kg (35.97 lb)

Valve Stem Thickness

(intake)

(exhaust)

4.972-4.987 mm
4.960-4.975 mm

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды