Arctic Cat HDX CREW 2017 Скачать руководство пользователя страница 20

Страница: 20 / 152

PR917

7. Disconnect the two EPS connectors.

8. Remove the cap screws securing the EPS assembly

to the frame; then remove the cap screw securing the

rack coupler to the EPS output shaft.

PR761A



NOTE: The EPS assembly is not a serviceable com-

ponent and must be replaced as a complete assembly.

9. Remove the EPS from the top side.

INSTALLING STEERING SHAFT/EPS
ASSEMBLY

1. Install the EPS into position.

2. Align the slot in the rack coupler to the notch in the

frame (front wheels centered).

PR766A



NOTE: Steps 3-5 are for the EPS models only.

3. Rotate the EPS shaft to align the index (flattened)

spline with the slot in the rack coupler and install the

EPS assembly into the coupler; then seat the EPS

firmly onto the frame.

PR776A

4. Install the cap screws securing the EPS assembly to

the frame and tighten to 35 ft-lb. Install the cap

screw and new lock nut in the EPS to rack coupler

and tighten to 11 ft-lb.

5. Connect the two electrical connectors; then align the

slot in the steering shaft coupler to the index (flat-

tened) spline on the EPS input shaft and install.

Install but do not tighten the cap screw.

PR759B

6. Install the steering shaft housing. Secure to the frame

with two cap screws and nuts. Tighten to 20 ft-lb.

PR897

7. Tighten the cap screw (from step 6) to 25 ft-lb.

8. Install the front storage box.

9. Connect the regulator/rectifier and install the coolant

bottle to the front storage box. Tighten the regulator/

rectifier to 8 ft-lb and the coolant bottle to 48 in.-lb.

10. Install the dash and connect the electrical connectors.

Secure with screws and tighten securely. Do not

over-tighten.

11. Connect the tilt steering mechanism and tighten

securely. Install the shift knob.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды