Arctic Cat HDX CREW 2017 Скачать руководство пользователя страница 136

Страница: 136 / 152

135

2. Lubricate the splines of the driveshaft with the

appropriate grease; then align and engage the drive-

line flange to the engine flange. Tighten to 20 ft-lb.

3. Secure the differential to the frame/frame bracket

with two through-bolts and secure with lock nuts and

flat washers. Tighten to 38 ft-lb.

4. Install the rear drive axles; then install the brake cali-

pers and tighten the new “patch-lock” cap screws to

20 ft-lb.

5. Fill the gear case with the appropriate lubricant; then

install the left side storage box.

Hub

REMOVING

1. Secure the vehicle on a support stand to elevate the

wheel; then remove the wheel(s).



NOTE: The jack stands should be placed under the

main frame to avoid contact with front suspension

components.



NOTE: Removing or tightening of the hub nuts

requires the axles be locked. To lock the rear axle,

place the transmission in park. To lock the front axle,

turn the ignition switch to ON and select LOCK on

the drive select switch; then place the transmission in

park and turn the ignition switch to OFF.

2. Remove the cotter pin from the hub retaining plate.

Discard the cotter pins.

PR960

3. Remove the hub nut securing the hub.

4. Remove the brake caliper(s).



NOTE: It is not necessary to remove the brake hoses

from the calipers for this procedure.

PR264A

5. Remove the hub assembly.

6. Remove the four cap screws securing the brake disc.

PR254A

CLEANING AND INSPECTING

1. Clean all hub components.

2. Inspect all threads for stripping or damage.

3. Inspect the brake disc (if applicable) for cracks or

warping.

4. Inspect the hub for pits, cracks, loose studs, or spline

wear.

REPLACING WHEEL STUDS

1. Secure the hub in a suitable holding fixture and

remove the brake disc (if applicable).

2. Drive the damaged stud out of the hub; then place the

new stud into the hub and thread on an appropriate

flange nut.

PR250

3. Using a socket and ratchet handle, tighten the nut

until the stud is fully drawn into the hub.

! WARNING

Make sure the vehicle is solidly supported on the sup-
port stand to avoid injury.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды