Arctic Cat HDX CREW 2017 Скачать руководство пользователя страница 23

Страница: 23 / 152

PR289

CLEANING AND INSPECTING

1. Clean all knuckle components.

2. Inspect the bearing for pits, scoring, rusting, or pre-

mature wear.

3. Inspect the knuckle for cracks, breaks, or galling of

the bearing surface.

ASSEMBLING AND INSTALLING

1. Using a suitable press and driver, press the bearing

into the knuckle until firmly seated; then install the

snap ring.

PR292A

PR289

2. Install the knuckle to the upper and lower ball joints

and secure with the two cap screws. Tighten to 35 ft-

lb.

PR202

PR203

3. Install the tie rod end and secure with the nut (coated

with red Loctite #271). Tighten to 30 ft-lb; then

install a new cotter pin and spread the pin.



NOTE: During assembling, new cotter pins should

be installed.

4. Apply a small amount of molybdenum grease to the

hub splines.

PR290A

5. Install the hub assembly onto the splines of the shaft.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды