Arctic Cat HDX CREW 2017 Скачать руководство пользователя

Страница: 147 / 152

146

PR193

5. Tap the ball joints out of the knuckle; then remove

the knuckle.

6. Remove the lower shock absorber eyelet from the

upper A-arm.

HDX293

7. Remove the cap screws securing the A-arms to the

frame.

HDX296

8. Remove the snap ring from the ball joint; then

remove the ball joint from the A-arm.

HDX297

CLEANING AND INSPECTING

1. Clean all A-arm components in parts-cleaning sol-

vent.

2. Clean the ball joint mounting hole of all residual

Loctite, grease, oil, or dirt for installing purposes.

3. Inspect the A-arm for bends, cracks, and worn bush-

ings.

4. Inspect the ball joint mounting holes for cracks or

damage.

5. Inspect the frame mounts for signs of damage, wear,

or weldment damage.

INSTALLING

1. Apply Loctite Primer “T” to the A-arm socket; then

apply green Loctite #609 to the entire outside diame-

ter of the ball joint. Install the ball joint into the A-

arm and secure with the snap ring.

HDX297

2. Install the A-arm assemblies into the frame mounts

and secure with the cap screws. Only finger-tighten

at this time.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды