Arctic Cat HDX CREW 2017 Скачать руководство пользователя страница 126

Страница: 126 / 152

125

3. To increase end-play, decrease the shim thickness. To

decrease end-play, increase the shim thickness.



NOTE: Once proper backlash and end play are

established, the gear case can be assembled.

Assembling Differential Assembly

1. With the pinion gear and new bearings installed,

place the selected (backlash) shim on the gear case

side of the ring gear with the chamfered side toward

the ring gear; then install into gear case/differential

housing.

GC031A

GC020

2. Place the selected (end-play) shim, chamfered side

toward the gear, onto the cover side of the ring gear.

GC036B



NOTE: The spider and ring gear assembly must be

replaced as a complete unit.

3. Assemble the fork and sliding collar into the cover

assembly; then install the left bearing flange/bearing

assembly and seat firmly into the cover.

CF266A

CF267A

4. Apply a liberal coat of grease to the O-ring; then

install it on the assembled cover assembly making

sure to seat the O-ring completely down around the

circumference of the bearing flange.

CF275A

5. Making sure the O-ring is properly positioned on the

differential housing cover assembly, install the cover

with existing cap screws (coated with green Loctite

#270). Tighten the cap screws evenly to 23 ft-lb.



NOTE: Grease can be applied to the O-ring for ease

of assembling.



NOTE: If a new housing is being installed, tighten

the cap screws to 28 ft-lb.

6. Install the shift fork shaft w/spring into the housing

making sure the shaft O-ring is positioned to the

inside.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды