Arctic Cat HDX CREW 2017 Скачать руководство пользователя

Страница: 58 / 152

CF060A

2. If damaged, the camshaft must be replaced.

Installing Top-Side

Components

A. Piston
B. Cylinder

1. Install the piston on the connecting rod making sure

the circlip on each side is fully seated in the piston.



NOTE: The piston should be installed so the arrow

points toward the exhaust.

CC032D

2. Place the two alignment pins into position. With

sealant applied to the crankcase mating area, place

the cylinder gasket into position; then place a piston

holder (or suitable substitute) beneath the piston skirt

and square the piston in respect to the crankcase.

CC026D

3. Lubricate the inside wall of the cylinder; then using a

ring compressor or the fingers, compress the rings

and slide the cylinder over the piston. Route the cam

chain up through the cylinder cam chain housing;

then remove the piston holder and seat the cylinder

firmly on the crankcase.

CC024D

4. Loosely install the two nuts which secure the cylin-

der to the crankcase.



NOTE: The two cylinder-to-crankcase nuts will be

tightened in step 11.

CC023D

5. Install the coolant hose onto the crankcase union and

tighten the clamp.

C. Cylinder Head
D. Valve Cover



NOTE: Steps 1-5 in the preceding sub-section must

precede this procedure.

6. Place the chain guide into the cylinder.

CAUTION

The cylinder should slide on easily. Do not force the cyl-
inder or damage to the piston, rings, cylinder, or crank-
shaft assembly may occur.

CAUTION

Care should be taken that the bottom of the chain guide
is secured in the crankcase boss.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды