Arctic Cat HDX CREW 2017 Скачать руководство пользователя

Страница: 96 / 152

Electrical System

The electrical connections should be checked periodi-

cally for proper function.

TESTING ELECTRICAL COMPONENTS

All electrical tests should be made using the CATT II or

the Fluke Model 77 Multimeter. The CATT II can return

data for certain components which are identified at the

beginning of their respective sub-section. If any other

type of meter is used, readings may vary due to internal

circuitry. When troubleshooting a specific component,

always verify first that the fuse(s) are good, that the

LED(s) are good, that the connections are clean and tight,

that the battery is fully charged, and that all appropriate

switches are activated.



NOTE: For absolute accuracy, all tests should be

made at room temperature of 68° F.



NOTE: Certain components and sensors can be

checked by using the EFI diagnostic system (see EFI

Diagnostic System in this section for more informa-

tion).

SPECIAL TOOLS

A number of special tools must be available to the techni-

cian when performing service procedures in this section.

Refer to the current Special Tools Catalog for the appro-

priate tool description.



NOTE: When indicated for use, each special tool

will be identified by its specific name, as shown in the

chart below, and capitalized.



NOTE: Special tools are available from the Arctic

Cat Service Department.

Battery



NOTE: Preliminary checks may be performed on

this component using the diagnostic mode on the LCD

gauge (see EFI Diagnostic System in this section)

Battery

1. The battery is located below the rear seat on the

driver’s side. When installing the battery, always con-

nect the positive cable first, then connect the negative

cable. When removing the batter, disconnect the nega-

tive cable first, then disconnect the positive cable.

2. Ensure the battery positive cable is routed along the

main harness opposite side of the engine and secured

using two cable ties as shown. If it is ever required

these two cable ties be removed, replacement cable

ties should be installed in the same exact location.

HDX411A

After being in service, batteries require regular cleaning

and recharging in order to deliver peak performance and

maximum service life. The following procedures are rec-

ommended for cleaning and maintaining lead-acid batter-

ies. Always read and follow instructions provided with

battery chargers and battery products.



NOTE: Refer to all warnings and cautions provided

with the battery or battery maintainer/charger.

Loss of battery charge may be caused by ambient tem-

perature, ignition OFF current draw, corroded terminals,

self discharge, frequent start/stops, and short engine run

times. Frequent winch usage, snowplowing, extended

low RPM operation, short trips, and high amperage

accessory usage are also reasons for battery discharge.

Maintenance Charging



NOTE: Arctic Cat recommends the use of the

CTEK Multi US 800 or the CTEK Multi US 3300 for

battery maintenance charging. Maintenance charging

is required on all batteries not used for more than two

weeks or as required by battery drain.

1. When charging a battery in the vehicle, be sure the

ignition switch is in the OFF position.



NOTE: Be sure to maintain the fluid of the battery

at the UPPER LEVEL. Use only distilled water when

adding fluid to these batteries.

2. Clean the battery terminals with a solution of baking

soda and water.

3. Be sure the charger and battery are in a well-venti-

lated area and ensure the battery charger cables will

not contact any battery acid. Be sure the charger is

unplugged from the 110-volt electrical outlet.

4. Connect the red terminal lead from the charger to the

positive terminal of the battery; then connect the

black terminal lead of the charger to the negative ter-

minal of the battery.

5. Plug the battery charger into a 110-volt electrical

outlet.

Description

p/n

Fluke Model 77 Multimeter

0644-559

CATT II

0544-029

MaxiClips

0744-041

Test Plug/Code List

0486-219

Component data can be retrieved using the CATT II. Uti-
lize the Sensor Data screen.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды