Arctic Cat HDX CREW 2017 Скачать руководство пользователя

Страница: 35 / 152

HDX344A

INSTALLING

1. Secure the latch to the frame with new cap screws

and lock nuts.

2. Install the front row plastic side panels (center); then

secure with the cap screws.

3. Install the front splash panels and front outer fenders;

then secure with the cap screws.

Dashboard

REMOVING

1. Remove the steering wheel, shift lever knob, and

front access panel.

PR890A

2. Remove the hood seal; then disassemble and remove

all four front fenders (outer fenders first).

HDX267A

HDX268A

3. Remove the cap screws around the perimeter of the

dashboard.

ROV-887

4. From under the dashboard, disconnect the accessory

plugs, override switch, drive select switch, and igni-

tion switch. Note the orientation of the connectors

for installing purposes.

5. Remove the instrument gauge from the dashboard

and disconnect it; then remove the cap screws secur-

ing the steel access plate on the driver’s side behind

the dashboard. Disconnect the headlight switch con-

nector.

HDX269

6. Remove the upper cap screw and lock nut from the

tilt steering sub-assembly and support lift. Discard

the locknut.

CENTER

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды