Can-Am DS 450 EFI Operator'S Manual Download

Page: 1 / 144

THIS VEHICLE CAN BE HAZARDOUS TO OPERATE.

A collision or rollover can occur quickly, even during

routine maneuvers such as turning and driving on hills

or over obstacles, if you fail to take proper precautions.

SEVERE INJURY OR DEATH

can result if

you do not follow these instructions:

BEFORE YOU OPERATE THIS VEHICLE, READ

THIS

OPERATORS GUIDE

AND ALL ON-

PRODUCT LABELS.

 NEVER OPERATE THIS VEHICLE WITHOUT

PROPER INSTRUCTIONS.

Beginners should

complete a certified training course.

NEVER CARRY A PASSENGER.

You increase

your risk of losing control if you carry a passenger.

 NEVER OPERATE THIS VEHICLE ON A PAVED

SURFACE.

You increase your risk of losing control

if you operate this vehicle on pavement.

 NEVER OPERATE THIS VEHICLE ON PUBLIC

ROADS.

You can collide with another vehicle if you

operate this vehicle on a public road.

 ALWAYS WEAR AN APPROVED HELMET,

eye protection, and protective clothing.

 NEVER RIDE UNDER THE INFLUENCE OF

ALCOHOL OR DRUGS.

They slow reaction time and

impair judgment.

 NEVER OPERATE THIS VEHICLE AT EXCESSIVE

SPEEDS.

You increase your risk of losing control

if you operate this vehicle at speeds too fast for the

terrain, visibility conditions, or your experience.

NEVER ATTEMPT WHEELIES, JUMPS, OR OTHER

STUNTS.

WARNING

Read this guide thoroughly. It contains important safety information.

Minimum recommended operators age: 16 years old.

Do not remove this Operators Guide from the vehicle.

WARNING

® AND THE BRP LOGO ARE TRADEMARKS OF BOMBARDIER RECREATIONAL PRODUCTS INC. OR ITS AFFILIATES.

219 000 576

OPERATORS GUIDE, DS 450 EFI/ X xc/ ENGLISH

GUIDE DU CONDUCTEUR, DS 450 EFI/ X xc/ ANGLAIS

FAIT AU / MADE IN CANADA

U/M:P.C.

2 1 9 0 0 0 5 7 6

Includes

Safety, Vehicle

and

Maintenance Information

Operators

Guide

450

EFI

450

EFI

450

EFI

450

EFI

Summary of Contents for DS 450 EFI

















































































































































Search results

Summary of Contents for DS 450 EFI

Reviews:

Related manuals for DS 450 EFI

Brands by name

Popular brands

Can-Am DS 450 EFI, Operator'S Manual

Search results

Summary of Contents for DS 450 EFI

Reviews:

Related manuals for DS 450 EFI

Brands by name

Popular brands