Siemens SINUMERIK 810D Diagnostic Manual Download Page 867

Page: 867 / 880

11/2006

Error Codes of Alarm 300500

4-867

SINUMERIK, SIMODRIVE Diagnostics Manual (DA), 11/2006 Edition

Extension 2

Explanation

Performance 1 and standard cannot run two axes with HSA.

Remedy

Only one HSA axis may be active.

Error code

0048H

Error text

Unexpected measurement system configuration

Extension 1

Extension 2

Explanation

The PCU extension for direct or indirect measurement systems is incomplete.

Remedy

Check module.

Error code

0049H

Error text

A CCU3 axis was defined as a single-axis model.

Extension 1

Extension 2

Explanation

Remedy

Error code

0050H

Error text

Module not supported by drive software.

Extension 1

Extension 2

Explanation

The drive software cannot be run on this module.

Remedy

Load the drive software for the module or plug in the correct module for the drive soft-
ware.

Summary of Contents for SINUMERIK 810D











































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SINUMERIK 810D

Reviews:

Related manuals for SINUMERIK 810D

Brands by name

Popular brands

Siemens SINUMERIK 810D, Diagnostic Manual

Search results

Summary of Contents for SINUMERIK 810D

Reviews:

Related manuals for SINUMERIK 810D

Brands by name

Popular brands