Siemens SINUMERIK 810D Diagnostic Manual Download Page 625

Page: 625 / 880

HMI alarms

11/2006

Overview of Alarms

2-625

SINUMERIK, SIMODRIVE Diagnostics Manual (DA), 11/2006 Edition

101163

MDx130 MOTOR_NOMINAL_POWER <= 0

Definitions:

Remedy:

101164

MDx132 MOTOR_NOMINAL_VOLTAGE <= 0

Definitions:

Remedy:

101165

MDx103 MOTOR_NOMINAL_CURRENT <= 0

Definitions:

Remedy:

101166

MDx129 POWER_FACTOR_COS_PHI illegal

Definitions:

Remedy:

101167

MDx134/MDx400
MOTOR_NOMINAL_FREQUENCY/MOTOR_RATED_SPEED illeg.

Definitions:

Remedy:

101168

Warning MDx142 FIELD_WEAKENING_SPEED<MDx400
MOTOR_RATED_SPEED

Definitions:

Remedy:

101169

Date and time could not be set!

Definitions:

Remedy:

101200

Safety Integrated data copied

Definitions:

The SI data copying function was successfull.

Remedy:

101201

Safety Integrated data confirmed

Definitions:

The SI data confirmation function was successfull.

Remedy:

101202

Copying SI data from axis %1 to drive %2

Parameters:

%1 = Axis name
%2 = Drive number

Definitions:

This message is output during the SI data copying function.

Remedy:

101203

SI data not copied completely

Definitions:

An error occurred during the SI data copying function; this caused the SI data to be copied
incompletely or not at all.

Remedy:

Summary of Contents for SINUMERIK 810D











































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SINUMERIK 810D

Reviews:

Related manuals for SINUMERIK 810D

Brands by name

Popular brands

Siemens SINUMERIK 810D, Diagnostic Manual

Search results

Summary of Contents for SINUMERIK 810D

Reviews:

Related manuals for SINUMERIK 810D

Brands by name

Popular brands