Siemens SINUMERIK 810D Diagnostic Manual Download Page 748 | Manualshive

Page: 748 / 880

background image

Overview of Alarms

11/2006

SIMODRIVE alarms

2-748

©

Siemens AG, 2006. All rights reserved

SINUMERIK, SIMODRIVE Diagnostics Manual (DA), 11/2006 Edition

300767

Axis %1 drive %2 natural frequency > Shannon frequency

Parameters:

%1 = NC axis number
%2 = Drive number

Definitions:

The natural frequency of a speed setpoint filter is greater than the Shannon sampling frequency from
the sampling theorem.
The alarm can be reprogrammed in the MD ALARM_REACTION_CHAN_NOREADY (channel not
ready).

Reaction:

NC not ready.
The NC switches to follow-up mode.
Channel not ready.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.
Channel not ready.

Remedy:

Please inform the authorized personnel/service department.
The natural frequency in Hz of a speed setpoint filter must be less than the reciprocal value of two
speed controller cycles.
Speed setpoint filter 1:
MD 1520 * 0.01 * MD 1514 < 1 / ( 2 * MD 1001 * 31.25 microsec)
Speed setpoint filter 2:
MD 1521 * 0.01 * MD 1517 < 1 / ( 2 * MD 1001 * 31.25 microsec)
- Modify MD 1520: $MD_SPEED_FILTER_1_BS_FREQ (bandstop filter natural frequency speed
setpoint filter 1)
- Modify MD 1514: $MD_SPEED_FILTER_1_SUPPR_FREQ (suppression frequency speed setpoint
filter 1) 1)
- Modify MD 1521: $MD_SPEED_FILTER_2_BS_FREQ (bandstop filter natural frequency speed
setpoint filter 2)
- Modify MD 1517: $MD_SPEED_FILTER_2_SUPPR_FREQ (suppression frequency speed setpoint
filter 2) 2)
- Modify MD 1001: $MD_SPEEDCTRL_CYCLE_TIME (speed controller cycle)

Program
Continuation:

Clear alarm with the RESET key in all channels. Restart part program.

«
...
746
747
748
749
750
...
»

Summary of Contents for SINUMERIK 810D

















































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SINUMERIK 810D

Brand: Saito Pages: 90

Brand: Vancare Pages: 31

Brand: Eaton Pages: 12

Brand: Saga Pages: 9

Brand: Gardena Pages: 14

Brand: Gardena Pages: 4

Brand: Garaventa Lift Pages: 58

Brand: Union Instruments Pages: 63

Brand: Yamaha Pages: 92

ArtNet-DMX Mux16

Brand: DMX4ALL Pages: 21

RDS17S-ELITE1-R1

Brand: D&R ELECTRONICS Pages: 12

iDual A E27 iD60

Brand: jedi LIGHTING Pages: 23

Brand: S&C Pages: 26

Brand: Barton Pages: 36

U-verse Advance Series A10

Brand: AT&T Pages: 2

Brand: Goodson Pages: 4

Brand: Moeller Pages: 2

Brand: Sielco Elettronica Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands