manualshive.com logo in svg

Siemens SINUMERIK 810D, Diagnostic Manual

The Siemens SINUMERIK 810D Operator's Manual is a comprehensive guide for operating and programming this advanced numerical control system. Easily download this manual for free from our website, providing you with the necessary instructions and insights to maximize the potential of your SINUMERIK 810D.

Share
Download
background image

NCK alarms

11/2006

Overview of Alarms

 

2-195

©

 Siemens AG, 2006. All rights reserved

SINUMERIK, SIMODRIVE Diagnostics Manual (DA), 11/2006 Edition

 

14013

Channel %1 block %2 number of subroutine passes invalid

Parameters:

%1 = Channel number
%2 = Block number, label

Definitions:

In a subroutine call the programmed number of passes P is zero or negative.

Reaction:

Correction block is reorganized.
Interface signals are set.
Alarm display.

Remedy:

Program number of passes between 1 and 9 999.

Program 
Continuation:

Clear alarm with NC START or RESET key and continue the program.

14014

Channel %1 selected program %3 not available or will be edited

Parameters:

%1 = Channel number
%2 = Block number, label
%3 = Program name

Definitions:

The selected parts program is not in the NCK memory or the access authorization for the program 
selection is from a higher level than the current control status.
During creation, this program received the protection level of the NC control which was active at the 
time.
In SW 5 or higher a program edited on HMI can no longer be started with NC Start.
The alarm will also be issued, if a file other than the specified definition file has been selected for the 
GUD or macro definition.

Reaction:

Alarm display.

Remedy:

Reload the program in the NCK memory or check and correct the name of the directory (workpiece 
overview) and the program (program overview) and reselect.

Program 
Continuation:

Clear alarm with the Delete key or NC START.

14015

Channel %1 block %2 program %3 is not enabled

Parameters:

%1 = Channel number
%2 = Block number, label
%3 = Program name

Definitions:

The execution right currently set in the control (e.g. key switch position 0) is inadequate to execute 
part program %3.  

Reaction:

Correction block is reorganized.
Interface signals are set.
Alarm display.

Remedy:

- Raise the execution right to match the protection level of part program %3
- Assign a lower protection level to part program %3 or release (key switch protection level 0)

Program 
Continuation:

Clear alarm with NC START or RESET key and continue the program.

Summary of Contents for SINUMERIK 810D

















































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SINUMERIK 810D

Nelsen Corporation C Series Programming Manual preview
C Series
Brand: Nelsen Corporation Pages: 16
National Instruments C Series Calibration Procedure preview
C Series
Brand: National Instruments Pages: 8
National Instruments C Series Getting Started preview
C Series
Brand: National Instruments Pages: 34
Bard ECU Series Advanced Programming & Features preview
ECU Series
Brand: Bard Pages: 8
Bardiani Valvole B925 Use And Maintenance Manual preview
B925
Brand: Bardiani Valvole Pages: 35
Eaton ePDU G3 Installation & Quick Start Manual preview
ePDU G3
Brand: Eaton Pages: 2
Eaton ePDU G3 Manual preview
ePDU G3
Brand: Eaton Pages: 2
Eaton PowerXL DX-NET-ETHERCAT-2 Instruction Leaflet preview
PowerXL DX-NET-ETHERCAT-2
Brand: Eaton Pages: 3
MAKOT UMS-02 Manual preview
UMS-02
Brand: MAKOT Pages: 6
Rane ZR1 Datasheet preview
ZR1
Brand: Rane Pages: 2
U-Prox IC L Installations preview
IC L
Brand: U-Prox Pages: 3
Vizio Xrt302 Manual preview
Xrt302
Brand: Vizio Pages: 65
A.R.I. K-060VB M1 Installation Operation & Maintenance preview
K-060VB M1
Brand: A.R.I. Pages: 14
Industrial Controls MC-2120 Operating And Maintenance Manual preview
MC-2120
Brand: Industrial Controls Pages: 17
SolarEdge PV530-R72LGML Installation Manual preview
PV530-R72LGML
Brand: SolarEdge Pages: 20
PrimaLuceLab EAGLE CORE PLUS Manual preview
EAGLE CORE PLUS
Brand: PrimaLuceLab Pages: 40
Hoover 59132-297 Owner'S Manual preview
59132-297
Brand: Hoover Pages: 12
G-Tech FIELD MATE User Manual And Installation Manual preview
FIELD MATE
Brand: G-Tech Pages: 26

Brands by name

Popular brands

Load more brands