Siemens SINUMERIK 810D Diagnostic Manual Download Page 865

Page: 865 / 880

11/2006

Error Codes of Alarm 300500

4-865

SINUMERIK, SIMODRIVE Diagnostics Manual (DA), 11/2006 Edition

Extension 2

0x60 ;Illegal SERVO reaction on STF handshake

0x61 ;Error during RAM check

0x62 ;Transport checksum does not correspond to that of the SERVO.

Explanation

Errors were detected on loading the drive software. The cause is either faults during the
transfer via the drive bus or a defective control module.

Remedy

Check the drive bus cable and cable connections, perform remedial measures
(check shielding or ground connection), replace control module

Error code

0035H

Error text

Error in software boot section 2

Extension 1

0 or incorrect address

Extension 2

0x60 ;Illegal SERVO reaction on STF handshake

0x61 ;Error during RAM check

0x62 ;Transport checksum does not correspond to that of the SERVO.

Explanation

Errors were detected on loading the drive software. The cause is either faults during the
transfer via the drive bus or a defective control module.

Remedy

Check the drive bus cable and cable connections, perform remedial measures (check
shielding or ground connection), replace control module.

Error code

0040H

Error text

Incorrect number of specified current state filters

Extension 1

Extension 2

Explanation

An illegal number of current setpoint filters (> 4) has been entered.

Remedy

Correct number of current setpoint filters (MD 1200)

Error code

0041H

Error text

Incorrect number of specified rotation speed state filters

Extension 1

Extension 2

Explanation

An illegal number of speed setpoint filters (> 2) has been entered.

Remedy

Correct the number of speed setpoint filters (MD 1500).

Error code

0044H

Error text

Difference GROBSYNC/FEINSYNC too great.

Extension 1

Summary of Contents for SINUMERIK 810D











































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SINUMERIK 810D

Reviews:

Related manuals for SINUMERIK 810D

Brands by name

Popular brands

Siemens SINUMERIK 810D, Diagnostic Manual

Search results

Summary of Contents for SINUMERIK 810D

Reviews:

Related manuals for SINUMERIK 810D

Brands by name

Popular brands