Siemens SINUMERIK 810D Diagnostic Manual Download Page 820

Page: 820 / 880

Overview of Alarms

11/2006

PLC alarms

2-820

SINUMERIK, SIMODRIVE Diagnostics Manual (DA), 11/2006 Edition

400275

Direct keys 2 failed

Definitions:

Direct keys 2: internal timeout has expired.

Reaction:

Alarm display.

Remedy:

Check connection to direct key module

Program
Continuation:

Internal

400276

Pointer parameter direct keys 1 incorrect

Definitions:

Pointer incorrectly defined

Reaction:

Alarm display.

Remedy:

Correct the pointer

Program
Continuation:

Switch control OFF - ON.

400277

Pointer parameter direct keys 2 incorrect

Definitions:

Pointer incorrectly defined

Reaction:

Alarm display.

Remedy:

Correct the pointer

Program
Continuation:

Switch control OFF - ON.

400551

Fault on MPI/DP bus

Definitions:

Error detected on I/O bus

Reaction:

Alarm display.

Remedy:

Check I/Os, rectify I/O fault

Program
Continuation:

Internal

400552

Fault on DP bus

Definitions:

Error detected on I/O bus

Reaction:

Alarm display.

Remedy:

Check I/Os, rectify I/O fault

Program
Continuation:

Internal

400553

Fault on PROFINET bus

Definitions:

Error detected on I/O bus

Reaction:

Alarm display.

Remedy:

Check I/Os, rectify I/O fault

Program
Continuation:

Internal

400601

Configuration loading points incorrect

Definitions:

The PLC configuration in the DB4 does not match the NC configuration

Reaction:

Alarm display.

Remedy:

Correct tool management start-up

Program
Continuation:

Switch control OFF - ON.

Summary of Contents for SINUMERIK 810D











































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SINUMERIK 810D

Reviews:

Related manuals for SINUMERIK 810D

Brands by name

Popular brands

Siemens SINUMERIK 810D, Diagnostic Manual

Search results

Summary of Contents for SINUMERIK 810D

Reviews:

Related manuals for SINUMERIK 810D

Brands by name

Popular brands