manualshive.com logo in svg

Siemens SINUMERIK 810D, Diagnostic Manual

The Siemens SINUMERIK 810D Operator's Manual is a comprehensive guide for operating and programming this advanced numerical control system. Easily download this manual for free from our website, providing you with the necessary instructions and insights to maximize the potential of your SINUMERIK 810D.

Share
Download
background image

Overview of Alarms

11/2006

SIMODRIVE alarms

 

2-716

©

 Siemens AG, 2006. All rights reserved

SINUMERIK, SIMODRIVE Diagnostics Manual (DA), 11/2006 Edition

 

- The axis must move freely (e.g. motor not stalled).
- Reduce high axis friction (increase P1019) 

Program 
Continuation:

Clear alarm with the RESET key in all channels of this mode group. Restart part program.

300611

Axis %1 drive %2 generator mode: Motion at rotor position identification

Parameters:

%1 = NC axis number
%2 = Drive number

Definitions:

During the measurement, the motor has turned by more than the permissible value entered in 
MD1020: $MD_MAX_TURN_ROTORPOS_IDENT (maximum rotation of the rotor position 
identification). The rotation can be caused by switching on a rotating motor or by the identification 
itself.
The alarm can be reprogrammed in the MD ALARM_REACTION_CHAN_NOREADY (channel not 
ready).

Reaction:

Mode group not ready.
The NC switches to follow-up mode.
Channel not ready.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.
Channel not ready.

Remedy:

Please inform the authorized personnel/service department.
- If the rotation was caused by the identification itself, and if the error occurs repeatedly, then reduce 
MD1019: $MD_CURRENT_ROTORPOS_IDENT (rotor position identification current) or increase 
MD1020: $MD_MAX_TURN_ROTORPOS_IDENT (maximum rotation of the rotor position 
identification).
- Rotor position identification with inductance: stall the motor during the identification
- Rotor position identification with movement: check the factor load mass/load moment of inertia 
MD1076: $MD_FACTOR_MASS / $MD_FACTOR_INERTIA and increase if necessary.

Program 
Continuation:

Clear alarm with the RESET key in all channels of this mode group. Restart part program.

300612

Axis %1 drive %2 illegal current during rotor position identification

Parameters:

%1 = NC axis number
%2 = Drive number

Definitions:

1. With rotor position identification active, the current was
>= 1.2 * 1.05 * INVERTER_MAX_CURRENT (MD 1107)
2. With rotor position definition active, the current was
>= MOTOR_MAX_CURRENT (MD 1104)

Reaction:

Mode group not ready.
The NC switches to follow-up mode.
Channel not ready.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.
Channel not ready.

Remedy:

Please inform the authorized personnel/service department. Check MD 1019 with rotor position 
identification active and, if necessary, reduce the setting.

Program 
Continuation:

Clear alarm with the RESET key in all channels of this mode group. Restart part program.

Summary of Contents for SINUMERIK 810D

















































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SINUMERIK 810D

B&G WR10 Quick Reference Manual preview
WR10
Brand: B&G Pages: 2
B&K SR10.1 Operation Manual preview
SR10.1
Brand: B&K Pages: 9
Campbell CR10 PROM Replacement Procedure preview
CR10 PROM
Brand: Campbell Pages: 8
D+H RZN 4503-T Original Instructions Manual preview
RZN 4503-T
Brand: D+H Pages: 36
D-Box HEMC Getting Started preview
HEMC
Brand: D-Box Pages: 4
D+H RZN 4416-M Manual preview
RZN 4416-M
Brand: D+H Pages: 36
Farfisa TD6100 Manual preview
TD6100
Brand: Farfisa Pages: 20
Racal Instruments 1266 Manual preview
1266
Brand: Racal Instruments Pages: 64
Häfele 633.03.298 Quick Start Manual preview
633.03.298
Brand: Häfele Pages: 2
Häfele 633.03.298 Operating Instructions Manual preview
633.03.298
Brand: Häfele Pages: 24
Hama Ni-1 Operating Instruction preview
Ni-1
Brand: Hama Pages: 7
Hama 12183 Operating Instruction preview
12183
Brand: Hama Pages: 44
RadioMaster POCKET Quick Start Manual preview
POCKET
Brand: RadioMaster Pages: 10
K&K M8000 Installation Instructions Manual preview
M8000
Brand: K&K Pages: 6
Paradox PCS300 Reference And Installation Manual preview
PCS300
Brand: Paradox Pages: 32
Parker ACR7000 Series Hardware Manual preview
ACR7000 Series
Brand: Parker Pages: 21
Parker AC890PX Series Quick Start Manual preview
AC890PX Series
Brand: Parker Pages: 26
Parallax 700-10016 Manual preview
700-10016
Brand: Parallax Pages: 3

Brands by name

Popular brands

Load more brands