Siemens SINUMERIK 810D Diagnostic Manual Download Page 826

Page: 826 / 880

Overview of Alarms

11/2006

PLC alarms

2-826

SINUMERIK, SIMODRIVE Diagnostics Manual (DA), 11/2006 Edition

411101

Impermissible Parameter Axis in FB11

Definitions:

Axis parameter not within the permissible range.

Reaction:

Alarm display.

Remedy:

Use permissible axis number.

Program
Continuation:

Internal

411501

Incorrect version of FB 15, > general reset, do not transmit FB 15 from
project

Definitions:

FB 15 does not match the basic program used.

Reaction:

Alarm display.

Remedy:

General PLC reset. Use correct version of the basic program.

Program
Continuation:

Internal

411502

Incorrect basic PLC program version

Definitions:

FB 15 does not match the basic program used.

Reaction:

Alarm display.

Remedy:

Load the basic program that matches the NCK version.

Program
Continuation:

Internal

428201

Diagnostic alarm

Definitions:

OB82 or OB86 has been triggered.

Reaction:

Alarm display.

Remedy:

Rectify the cause of the error displayed

Program
Continuation:

Switch control OFF - ON.

428221

Diagnostic alarm from diagnostics address %Z

Definitions:

OB82 or OB86 has been triggered.

Reaction:

Alarm display.

Remedy:

Rectify the cause of the error displayed

Program
Continuation:

Switch control OFF - ON.

428601

Module failure of the expansion unit

Definitions:

OB82 or OB86 has been triggered.

Reaction:

Alarm display.

Remedy:

Rectify the cause of the error displayed

Program
Continuation:

Switch control OFF - ON.

428602

Recurrence of module failure of the expansion unit

Definitions:

OB82 or OB86 has been triggered.

Reaction:

Alarm display.

Remedy:

Rectify the cause of the error displayed

Program
Continuation:

Switch control OFF - ON.

Summary of Contents for SINUMERIK 810D











































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SINUMERIK 810D

Reviews:

Related manuals for SINUMERIK 810D

Brands by name

Popular brands

Siemens SINUMERIK 810D, Diagnostic Manual

Search results

Summary of Contents for SINUMERIK 810D

Reviews:

Related manuals for SINUMERIK 810D

Brands by name

Popular brands