manualshive.com logo in svg

Siemens SINUMERIK 810D, Diagnostic Manual

The Siemens SINUMERIK 810D Operator's Manual is a comprehensive guide for operating and programming this advanced numerical control system. Easily download this manual for free from our website, providing you with the necessary instructions and insights to maximize the potential of your SINUMERIK 810D.

Share
Download
background image

NCK alarms

11/2006

Overview of Alarms

 

2-219

©

 Siemens AG, 2006. All rights reserved

SINUMERIK, SIMODRIVE Diagnostics Manual (DA), 11/2006 Edition

 

14146

Channel %1 block %2 CP or PTP movement without transformation not 
allowed

Parameters:

%1 = Channel number
%2 = Block number, label

Definitions:

The CP or PTP G code was programmed for a movement but no transformation was active.

Reaction:

Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.

Remedy:

Modify the program.

Program 
Continuation:

Clear alarm with the RESET key. Restart part program

14147

Channel %1 block %2 spline for orientation not possible.

Parameters:

%1 = Channel number
%2 = Block number, label

Definitions:

If an orientation has been programmed while BSPLINE is active, the interpolation of
tool orientation must be interpolated via a 2nd space curve. This means that G code ORICURVE
must be active for the interpolation of the orientation.

Reaction:

Correction block is reorganized.
Interpreter stop
Interface signals are set.
Alarm display.

Remedy:

Change the NC program.

Program 
Continuation:

Clear alarm with NC START or RESET key and continue the program.

14148

Channel %1 illegal reference system for Cartesian manual traverse

Parameters:

%1 = Channel number

Definitions:

In the setting data SC_CART_JOG_MODE, an illegal value has been entered for the reference 
system with Cartesian manual travel.

Reaction:

Alarm display.

Remedy:

Enter a permitted value in the setting data SC_CART_JOG_MODE.

Program 
Continuation:

Clear alarm with the RESET key. Restart part program

14150

Channel %1 block %2 illegal tool carrier number programmed or 
declared (MD)

Parameters:

%1 = Channel number
%2 = Block number, label

Definitions:

A toolholder number was programmed which is negative or greater than the machine data 
MC_MM_NUM_TOOL_CARRIER.

Reaction:

Correction block is reorganized.
Interface signals are set.
Alarm display.

Remedy:

Please inform the authorized personnel/service department. Program valid toolholder number or 
adapt machine data MC_MM_NUM_TOOL_CARRIER.

Program 
Continuation:

Clear alarm with NC START or RESET key and continue the program.

Summary of Contents for SINUMERIK 810D

















































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SINUMERIK 810D

Balboa GL Series User Manual preview
GL Series
Brand: Balboa Pages: 12
Paoli F1 Operating And Maintenance Manual preview
F1
Brand: Paoli Pages: 16
Calpeda IDROMAT 5 Quick Start Manual preview
IDROMAT 5
Brand: Calpeda Pages: 4
ICM Controls ICM325HN Installation, Operation & Application Manual preview
ICM325HN
Brand: ICM Controls Pages: 2
Neets echo plus User Manual preview
echo plus
Brand: Neets Pages: 12
National Instruments NI 9871 Operating Instructions And Specifications preview
NI 9871
Brand: National Instruments Pages: 24
RAPIBREW FREDDA 1.0 Quick Start Manual preview
FREDDA 1.0
Brand: RAPIBREW Pages: 16
RAKwireless RAK3172 User Manual preview
RAK3172
Brand: RAKwireless Pages: 6
YASKAWA U1000 iQpump Drive Quick Start Quide preview
U1000 iQpump Drive
Brand: YASKAWA Pages: 26
YASKAWA Z1000 CIMR-ZU*A Series Quick Start Up Manual preview
Z1000 CIMR-ZU*A Series
Brand: YASKAWA Pages: 2
YASKAWA SIEMENS CNC Series Maintenance Manual, Serviceman Handbook preview
CNC Series
Brand: YASKAWA SIEMENS Pages: 373
Haberl Electronic 1E0671-1 MCR2.9 User Manual preview
1E0671-1 MCR2.9
Brand: Haberl Electronic Pages: 9
J+J J4C Series Installation Instructions preview
J4C Series
Brand: J+J Pages: 2
Parker CK5-DN Quick Start Manual preview
CK5-DN
Brand: Parker Pages: 4
Jetter 60873050 Manual preview
60873050
Brand: Jetter Pages: 24
Challenger Lifts 4030EAX Installation, Operation & Maintenance Manual preview
4030EAX
Brand: Challenger Lifts Pages: 20
ICP DAS USA M-7067D Quick Start Manual preview
M-7067D
Brand: ICP DAS USA Pages: 6
M-system R7M-CT4E Instruction Manual preview
R7M-CT4E
Brand: M-system Pages: 7

Brands by name

Popular brands

Load more brands