manualshive.com logo in svg

Siemens SINUMERIK 810D, Diagnostic Manual

The Siemens SINUMERIK 810D Operator's Manual is a comprehensive guide for operating and programming this advanced numerical control system. Easily download this manual for free from our website, providing you with the necessary instructions and insights to maximize the potential of your SINUMERIK 810D.

Share
Download
background image

Overview of Alarms

11/2006

NCK alarms

 

2-178

©

 Siemens AG, 2006. All rights reserved

SINUMERIK, SIMODRIVE Diagnostics Manual (DA), 11/2006 Edition

 

12553

Channel %1 block %2 name %3 option/function is not active

Parameters:

%1 = Channel number
%2 = Block number, label
%3 = Source symbol

Definitions:

The option (if $MN_NC_LANGUAGE_CONFIGURATION = 1) or the NC function (if 
$MN_NC_LANGUAGE_CONFIGURATION = 3) 
related to this language command is not active.
But the name of the language command is known.
Each programming of this language command is rejected with this alarm.

Reaction:

Correction block is reorganized.
Interface signals are set.
Alarm display.

Remedy:

Press the NC Stop key and select the "Compensation block" function by pressing the PROGRAM 
CORRECT softkey. The cursor positions itself on the incorrect block.
- Correct the name used (in the case of a typing error).
- Activate the NC function (if a language command of an inactive function has been programmed).
- Enable the option required (if a language command of a function with a non-enabled option has been 
programmed).
See also $MN_NC_LANGUAGE_CONFIGURATION.

Program 
Continuation:

Clear alarm with NC START or RESET key and continue the program.

12554

Channel %1 block %2 replacement cycle %3 for the predefined 
procedure is missing.

Parameters:

%1 = Channel number
%2 = Block number, label
%3 = Cycle name

Definitions:

The replacement cycle that is to be called instead of the predefined procedure
is not present / unknown in the control.

Reaction:

Correction block is reorganized.
Interface signals are set.
Alarm display.

Remedy:

Press the NC stop key and select the "Compensation block" function by pressing the PROGRAM 
CORRECT softkey. The cursor will position itself in the faulty block.
- Correct the name used for the predefined procedure (write error)
- Or load the replacement cycle into one of the cycle directories (+ restart)
- Or set the machine data bit for the predefined procedure in $MN_COUPLE_CYCLE_MASK to 0 so 
that the predefined procedure is executed again.

Program 
Continuation:

Clear alarm with NC START or RESET key and continue the program.

Summary of Contents for SINUMERIK 810D

















































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SINUMERIK 810D

Jabra TAG Quick Start Manual preview
TAG
Brand: Jabra Pages: 18
Magellan MG5000 Programming Manual preview
MG5000
Brand: Magellan Pages: 44
Namron ZigBee Quick Start Manual preview
ZigBee
Brand: Namron Pages: 3
Omegalink 553 Quick Start Operation Manual preview
553
Brand: Omegalink Pages: 2
N-Com MCS II Instructions For Use Manual preview
MCS II
Brand: N-Com Pages: 20
N-Com BX5 User Instructions preview
BX5
Brand: N-Com Pages: 28
Parker CHELSEA Owner'S Manual preview
CHELSEA
Brand: Parker Pages: 32
Rayrun NT30 Quick Start Manual preview
NT30
Brand: Rayrun Pages: 4
PACH & COMPANY AeGIS 7000 Series Quick Start Manual preview
AeGIS 7000 Series
Brand: PACH & COMPANY Pages: 2
X Rocker 2.1 Wireless Manual preview
2.1 Wireless
Brand: X Rocker Pages: 38
L-Acoustics LA8 Product Information preview
LA8
Brand: L-Acoustics Pages: 20
Tech 21 MIDI MONGOOSE Owner'S Manual preview
MIDI MONGOOSE
Brand: Tech 21 Pages: 2
A.R.I. K-060VB M1 Installation Operation & Maintenance preview
K-060VB M1
Brand: A.R.I. Pages: 14
Industrial Controls MC-2120 Operating And Maintenance Manual preview
MC-2120
Brand: Industrial Controls Pages: 17
SolarEdge PV530-R72LGML Installation Manual preview
PV530-R72LGML
Brand: SolarEdge Pages: 20
Beckhoff CX2550 Series Manual preview
CX2550 Series
Brand: Beckhoff Pages: 30
Festo CPS-Gate Operating Instructions Manual preview
CPS-Gate
Brand: Festo Pages: 109
Topworx Valvetop DXP Installation, Operation & Maintenance Manual preview
Valvetop DXP
Brand: Topworx Pages: 8

Brands by name

Popular brands

Load more brands