manualshive.com logo in svg

Siemens SINUMERIK 810D, Diagnostic Manual

The Siemens SINUMERIK 810D Operator's Manual is a comprehensive guide for operating and programming this advanced numerical control system. Easily download this manual for free from our website, providing you with the necessary instructions and insights to maximize the potential of your SINUMERIK 810D.

Share
Download
background image

NCK alarms

11/2006

Overview of Alarms

 

2-411

©

 Siemens AG, 2006. All rights reserved

SINUMERIK, SIMODRIVE Diagnostics Manual (DA), 11/2006 Edition

 

25001

Axis %1 hardware fault of passive encoder

Parameters:

%1 = Axis name, spindle number

Definitions:

The signals from the position actual value encoder that is presently not active are missing, or they are 
not of the same phase, or they exhibit grounding/short-circuit.

Reaction:

Alarm display.

Remedy:

Please inform the authorized personnel/service department. Check measuring circuit connectors for 
correct contacting. Check encoder signals and replace the encoder if faults are found. Switch off the 
monitoring with the corresponding interface signal (DB 31 - 48, DBX 1.5 = 0 or DBX 1.6 = 0). o

Program 
Continuation:

Clear alarm with the RESET key. Restart part program

25010

Axis %1 pollution of measuring system

Parameters:

%1 = Axis name, spindle number

Definitions:

The encoder used for position control sends a contamination signal (only in measuring systems with 
contamination signal).
The alarm can be reprogrammed in the MD ALARM_REACTION_CHAN_NOREADY (channel not 
ready).

Reaction:

Mode group not ready.
The NC switches to follow-up mode.
Channel not ready.
NC Start disable in this channel.
Axes of this channel must be re-referenced.
Interface signals are set.
Alarm display.
NC Stop on alarm.
Channel not ready.

Remedy:

Please inform the authorized personnel/service department. Check the measuring system in 
accordance with the instructions given by the measuring device manufacturer.

Program 
Continuation:

Clear alarm with the RESET key in all channels of this mode group. Restart part program.

25011

Axis %1 pollution of passive encoder

Parameters:

%1 = Axis name, spindle number

Definitions:

The encoder not used for position control sends a contamination signal (only in measuring systems 
with contamination signal).

Reaction:

Alarm display.

Remedy:

Please inform the authorized personnel/service department. Check the measuring system in 
accordance with the instructions given by the measuring device manufacturer.

Program 
Continuation:

Clear alarm with the Delete key or NC START.

Summary of Contents for SINUMERIK 810D

















































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SINUMERIK 810D

Quectel BG96 At Command Manual preview
BG96
Brand: Quectel Pages: 23
Quectel BG96 Hardware Design preview
BG96
Brand: Quectel Pages: 79
Datavideo RMC-230 Instruction Manual preview
RMC-230
Brand: Datavideo Pages: 17
Datamax I-Class Installation And Operating Instructions Manual preview
I-Class
Brand: Datamax Pages: 22
LAIA TP-100 Administrator'S Manual preview
TP-100
Brand: LAIA Pages: 71
dbx DriveRack PA User Manual preview
DriveRack PA
Brand: dbx Pages: 52
Hankscraft Runxin HS Series Service Manual preview
HS Series
Brand: Hankscraft Runxin Pages: 58
Eaton ePDU G3 Installation & Quick Start Manual preview
ePDU G3
Brand: Eaton Pages: 2
Eaton ePDU G3 Manual preview
ePDU G3
Brand: Eaton Pages: 2
Eaton PowerXL DX-NET-ETHERCAT-2 Instruction Leaflet preview
PowerXL DX-NET-ETHERCAT-2
Brand: Eaton Pages: 3
Fagor CNC 8070 Original Instructions Manual preview
CNC 8070
Brand: Fagor Pages: 10
Fagor CNC 8070 Operating Manual preview
CNC 8070
Brand: Fagor Pages: 358
Fagor CNC 8070 Programming Manual preview
CNC 8070
Brand: Fagor Pages: 556
Fagor CNC 8060 Operating Manual preview
CNC 8060
Brand: Fagor Pages: 172
Fagor CNC 8060 Translation Of The Original Manual preview
CNC 8060
Brand: Fagor Pages: 180
Fagor CNC 8060 Hardware Configuration preview
CNC 8060
Brand: Fagor Pages: 112
FaderMate Master Control Unit Fittings Manual preview
Master Control Unit
Brand: FaderMate Pages: 36
FASAR ELETTRONICA FE230 Quick Start Manual preview
FE230
Brand: FASAR ELETTRONICA Pages: 2

Brands by name

Popular brands

Load more brands