Siemens SINUMERIK 808D Diagnostic Manual Download Page 60 | Manualshive

Page: 60 / 566

background image

Reaction:

NC not ready.
Mode group not ready, also effective for single axes.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.

Remedy:

Please inform the authorized personnel/service department. 3 MD identifiers are output, depending on the type of error.
1. MD30500 $MA_INDEX_AX_ASSIGN_POS_TAB: the error is due to multiple assignment of a position table MD10910

$MN_INDEX_AX_POS_TAB_1 or MD10930 $MN_INDEX_AX_POS_TAB_2) to axes with different types (linear/rotary axis).
2. MD10910 $MN_INDEX_AX_POS_TAB_1 or MD10930 $MN_INDEX_AX_POS_TAB_2: the contents of the displayed

tables are incorrect.
- The entered positions must be arranged in increasing size.
- A particular position must not be set more than once.
- If the table is assigned to one or several modulo axes, then the contents must be within the 0 to < 360 degree range.
3. MD10900 $MN_INDEX_AX_LENGTH_POS_TAB_1 or MD10920 $MN_INDEX_AX_LENGTH_POS_TAB_2: the length

of the displayed position table n was specified with 0.

Programm

continuation:

Clear alarm with the RESET key. Restart part program

4082

[channel %1: ] invalid value in machine date %2%3

Parameters:

%1 = Channel number
%2 = String: MD identifier
%3 = String: MD field index

Explanation:

A value has been entered which exceeds the value range or a limit value for a variable, a machine data or a function.

Reaction:

NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.

Remedy:

Enter correct values.

Programm

continuation:

Clear alarm with the RESET key. Restart part program

4090

Too many errors during power-up

Explanation:

More than <n> errors occurred during control power-up.

Reaction:

NC Start disable in this channel.
Alarm display.

Remedy:

Set the machine data correctly.

Programm

continuation:

Switch control OFF - ON.

4110

IPO cycle changed to %1 ms

Parameters:

%1 = String (new IPO cycle time)

Explanation:

The IPO cycle divisor was set to a value which was not an integral multiple of the position control cycle divisor. The divisor

(MD10070 $MN_IPO_SYSCLOCK_TIME_RATIO) was increased.
For PROFIBUS/PROFINET: MD10070 $MN_IPO_SYSCLOCK_TIME_RATIO has been modified because of the modified

DP cycle in the SDB (MD10050 $MN_SYSCLOCK_CYCLE_TIME).

Reaction:

Alarm display.

Remedy:

MD10070 $MN_IPO_SYSCLOCK_TIME_RATIO has been modified.

Programm

continuation:

Clear alarm with the RESET key. Restart part program

SINUMERIK 808D ADVANCED alarms
5.2 NCK alarms

Diagnostics Manual

60

Diagnostics Manual, 06/2015, 6FC5398-6DP10-0BA2

«
...
58
59
60
61
62
...
»

Summary of Contents for SINUMERIK 808D























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SINUMERIK 808D

Brand: J-Tech Digital Pages: 5

Brand: C4i Pages: 14

Brand: Labkotec Pages: 4

CORDED MOBILE CONNECTOR

Brand: Tesla Pages: 14

Brand: Smiths Pages: 9

Brand: Philips Pages: 2

Brand: Handson Technology Pages: 7

Brand: T&D Pages: 7

Brand: Comtrol Pages: 40

Brand: Essential Audio Tools Pages: 4

Brand: MAC Panel Pages: 2

Brand: cable matters Pages: 4

Brand: ATZ Pages: 4

Brand: ATZ Pages: 10

Brand: QPC Pages: 14

Brand: Audacy Pages: 10

Brand: Panduit Pages: 2

Brand: Kramer Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands