manualshive.com logo in svg

Siemens SINUMERIK 808D, Diagnostic Manual

The Siemens SINUMERIK 808D is an advanced CNC control system that offers precision and efficiency in machining. With its comprehensive Programming and Operating Manual, users can easily navigate and maximize the system's functionalities. Download the manual for free at manualshive.com and unlock the full potential of this groundbreaking product.

Share
Download
background image

61231

[Channel %1: ] Block %2: ShopMill program %4 not executable, as not tested by ShopMill

Parameters:

%1 = Channel number
%2 = Block number, label
%4 = Program name

Explanation:

Before a ShopMill program can be executed, it has to be tested by ShopMill.

Reaction:

Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.

Remedy:

The program first has to be simulated in ShopMill or loaded into the operating mode "Machine auto" by ShopMill.

Programm 

continuation:

Clear alarm with the RESET key. Restart part program

61232

[Channel %1: ] Block %2: Impossible to load magazine tool

Parameters:

%1 = Channel number
%2 = Block number, label

Explanation:

Only manual tools may be loaded into a swivel head in which only manual tools can be loaded.

Reaction:

Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.

Remedy:

Load a manual tool into the swivel head or set the parameter "Tool change" on the setup screen form "Rotary axes" to 

"Automatic".

Programm 

continuation:

Clear alarm with the RESET key. Restart part program

61233

[Channel %1: ] Block %2: Thread angle wrongly defined

Parameters:

%1 = Channel number
%2 = Block number, label

Explanation:

The thread angles were specified too large or too small.

Reaction:

Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.

Remedy:

Check thread geometry.

Programm 

continuation:

Clear alarm with the RESET key. Restart part program

61234

[Channel %1: ] Block %2: ShopMill subroutine %4 cannot be executed, as not tested by ShopMill

Parameters:

%1 = Channel number
%2 = Block number, label
%4 = Subroutine name

Explanation:

Before a ShopMill subroutine can be used, it has to be tested by ShopMill.

Reaction:

Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.

Remedy:

The subroutine first has to be simulated in ShopMill or loaded into the ShopMill operating mode "Machine auto".

Programm 

continuation:

Clear alarm with the RESET key. Restart part program

SINUMERIK 808D ADVANCED alarms

5.3 Cycle alarms

Diagnostics Manual

Diagnostics Manual, 06/2015, 6FC5398-6DP10-0BA2

411

Summary of Contents for SINUMERIK 808D























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SINUMERIK 808D

Quintex LB Series Operating Manual preview
LB Series
Brand: Quintex Pages: 30
StarTech.com SATRD30CM Quick Start Manual preview
SATRD30CM
Brand: StarTech.com Pages: 2
cable matters 102005 Quick Start Manual preview
102005
Brand: cable matters Pages: 2
Futek USB520 Quick Start Manual preview
USB520
Brand: Futek Pages: 16
Flair 858080 Instruction Manual preview
858080
Brand: Flair Pages: 5
Motorola RKN4136 Quick Start Manual preview
RKN4136
Brand: Motorola Pages: 8
Motorola RLN4853 Manual preview
RLN4853
Brand: Motorola Pages: 4
Motorola PMKN4003 User Manual preview
PMKN4003
Brand: Motorola Pages: 8
Altinex DA103-302 User Manual preview
DA103-302
Brand: Altinex Pages: 5
LAPP EPIC H-D 7 Assembly Instruction preview
EPIC H-D 7
Brand: LAPP Pages: 4
Lindy 42701 User Manual preview
42701
Brand: Lindy Pages: 2
Seeed BeagleBone Green HDMI Cape Quick Start Manual preview
BeagleBone Green HDMI Cape
Brand: Seeed Pages: 5
iCR iDR Quick Start preview
iDR
Brand: iCR Pages: 2
Sky SKY LINK Setup Manual preview
SKY LINK
Brand: Sky Pages: 15
HAZET-WERK 161N-3D Operating Instructions Manual preview
161N-3D
Brand: HAZET-WERK Pages: 16
Black Box PC to Printer Cable Specifications preview
PC to Printer Cable
Brand: Black Box Pages: 3
Mercury 429.950UK User Manual preview
429.950UK
Brand: Mercury Pages: 2
Steren 206-246 User Manual preview
206-246
Brand: Steren Pages: 2

Brands by name

Popular brands

Load more brands