manualshive.com logo in svg

Siemens SINUMERIK 808D, Diagnostic Manual

The Siemens SINUMERIK 808D is an advanced CNC control system that offers precision and efficiency in machining. With its comprehensive Programming and Operating Manual, users can easily navigate and maximize the system's functionalities. Download the manual for free at manualshive.com and unlock the full potential of this groundbreaking product.

Share
Download
background image

Programm 

continuation:

Clear alarm with the RESET key. Restart part program

22100

[Channel %1: ] Block %3 spindle %2 chuck speed exceeded

Parameters:

%1 = Channel number
%2 = Axis name, spindle number
%3 = Block number, label

Explanation:

The actual spindle speed is higher than the maximum speed configured in MD35100 $MA_SPIND_VELO_LIMIT plus a 

tolerance of 10 percent (fixed setting).
The alarm should not occur after correct optimization of the drive actuator and gear configuration.
This alarm can be reconfigured with MD11412  $MN_ALARM_REACTION_CHAN_NOREADY (channel not ready to 

operate) to 'BAG not ready'.
Note: Reconfiguring affects all alarms with alarm response 'Chan not ready'.

Reaction:

Mode group not ready.
Channel not ready.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.
Channel not ready.

Remedy:

Please inform the authorized personnel/service department. Check the setup and optimization data of the drive actuator 

in accordance with the Installation and Start-up Guide and make corrections.
Increase the tolerance window in MD35150 $MA_SPIND_DES_VELO_TOL.

Programm 

continuation:

Restart part program.    Clear alarm with the RESET key in all channels of this mode group. Restart part program.

22200

[Channel %1: ] Block %3 Spindle %2 axis stopped during tapping

Parameters:

%1 = Channel number
%2 = Axis name, spindle number
%3 = Block number, label

Explanation:

When tapping with compensating chuck (G63) the drilling axis was stopped via the NC/PLC interface and the spindle 

continues to rotate. The thread and possibly also the tap were damaged as a result.

Reaction:

NC Start disable in this channel.
Interface signals are set.
Alarm display.

Remedy:

Please inform the authorized personnel/service department. Provide an interlock in the PLC user program so that no axis 

stop can be initiated when tapping is active. If the tapping operation is to be terminated under critical machine conditions, 

the spindle and the axis should be stopped simultaneously if at all possible. Slight differences are then accommodated by 

the compensating chuck.

Programm 

continuation:

Clear alarm with the RESET key. Restart part program

22250

[Channel %1: ] Block %3 Spindle %2 axis stopped during thread cutting

Parameters:

%1 = Channel number
%2 = Axis name, spindle number
%3 = Block number, label

Explanation:

The thread cutting axis has been stopped while a thread block was active.
The stop can be caused by VDI signals that cause the feed to be interrupted.

Reaction:

NC Start disable in this channel.
Interface signals are set.
Alarm display.

SINUMERIK 808D ADVANCED alarms

5.2 NCK alarms

Diagnostics Manual

Diagnostics Manual, 06/2015, 6FC5398-6DP10-0BA2

331

Summary of Contents for SINUMERIK 808D























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SINUMERIK 808D

Icom opc-478uc Instruction Manual preview
opc-478uc
Brand: Icom Pages: 2
Panduit DPA245E88TV25 Installation Instructions preview
DPA245E88TV25
Brand: Panduit Pages: 2
ESI MIDIMATE eX User Manual preview
MIDIMATE eX
Brand: ESI Pages: 3
thomann Stairville DMX Splitter 8 USB 3 pin User Manual preview
Stairville DMX Splitter 8 USB 3 pin
Brand: thomann Pages: 32
Charmex TrauTech TSH314-HD User Manual preview
TrauTech TSH314-HD
Brand: Charmex Pages: 2
IFM Electronic E7377A Operating Instructions Manual preview
E7377A
Brand: IFM Electronic Pages: 44
SMC Networks Tiger Access Extended Ethernet Splitter SMC7048/VSP Brochure & Specs preview
Tiger Access Extended Ethernet Splitter SMC7048/VSP
Brand: SMC Networks Pages: 2
Burndy Continental Industries thermOweld CR-1 Instructions preview
Continental Industries thermOweld CR-1
Brand: Burndy Pages: 2
Yamaichi Electronics Y-Con Cover-20-TC Assembly Instructions preview
Y-Con Cover-20-TC
Brand: Yamaichi Electronics Pages: 2
Chauvet Synapse 4 User Manual preview
Synapse 4
Brand: Chauvet Pages: 20
Audio Technica ATW-49CB Quick Start Manual preview
ATW-49CB
Brand: Audio Technica Pages: 2
CommScope M2400 Series Instructions Manual preview
M2400 Series
Brand: CommScope Pages: 7
Lindy 38490-4 User Manual preview
38490-4
Brand: Lindy Pages: 8
Quell EESeal FilterSeal Insertion Instructions preview
EESeal FilterSeal
Brand: Quell Pages: 2
AVGear AVG-UDATP4 User Manual preview
AVG-UDATP4
Brand: AVGear Pages: 22
3M ECAM-20 MM-D Instructions Manual preview
ECAM-20 MM-D
Brand: 3M Pages: 18
3M 45116 User Manual preview
45116
Brand: 3M Pages: 9
3M Scotchlok U1 Series Instructions preview
Scotchlok U1 Series
Brand: 3M Pages: 2

Brands by name

Popular brands

Load more brands