Siemens SINUMERIK 808D Diagnostic Manual Download Page 216 | Manualshive

Page: 216 / 566

background image

Explanation:

An error occurred on the selection of JOG Retract, which is described in more detail by the error code (parameter%4):
List of error codes:
1: No retract data available
2: Selection is active during taper turning
3: Error preparing the initialization blocks. The additional info (parameter %3) states the initialization step in which the

error occurred. The alarm output immediately before also refers to this initialization step:
100: Error synchronizing the preprocessing/main run
101: Error selecting the tool length compensation
102: Error selecting the transformation
103: Error generating the tool frame
104: Error generating the tapping block
105: Error replacing geometry axes
4: The position of the axis stated in the additional info does not have the status "synchronized" or "restored"
5: The axis stated in the additional info is already assigned in another channel by JOG Retract
6: The geometry axis stated by the selection of JOG Retract does not exist
7: MD 20110 $MC_RESET_MODE_MASK bit 0 is not set
8: Thread cutting is active. The thread direction cannot be explicitly assigned to a JOG axis

Reaction:

Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.

Remedy:

The following conditions have to be fulfilled in order to select JOG Retract:
- A program execution with active tool offset has been canceled by Reset or PowerOff
- PLC signal DB3300.DBX4005.5 (Retract data available) or OPI variable retractState bit 1 is set
- JOG mode is active
- The channel in which JOG Retract is to be selected is in Reset state
- The function "Taper turning" must not be active when JOG Retract is selected
- Synchronized or restored axis positions must be present for the axes involved in the transformation
If necessary, activate position restoration for incremental encoders (MD34210 $MA_ENC_REFP_STATE[]=3)
- MD 20110 $MC_RESET_MODE_MASK bit 0 must be set (default value)
In the case of an error, the alarm must be acknowledged with Reset. The selection can then be repeated, observing the

above-mentioned conditions.

Programm

continuation:

Clear alarm with the RESET key. Restart part program

14750

[Channel %1: ] Block %2 too many auxiliary functions programmed

Parameters:

%1 = Channel number
%2 = Block number, label

Explanation:

More than 10 auxiliary functions have been programmed in an NC block.

Reaction:

Correction block is reorganized.
Interface signals are set.
Alarm display.

Remedy:

Check whether all auxiliary functions are necessary in one block - modal functions need not be repeated. Create separate

auxiliary function block or divide the auxiliary functions over several blocks.

Programm

continuation:

Clear alarm with NC START or RESET key and continue the program.

14751

[Channel %1: ] Block %2 resources for motion synchronous actions not sufficient (code: %3)

Parameters:

%1 = Channel number
%2 = Block number, label
%3 = Identifier

SINUMERIK 808D ADVANCED alarms
5.2 NCK alarms

Diagnostics Manual

216

Diagnostics Manual, 06/2015, 6FC5398-6DP10-0BA2

«
...
214
215
216
217
218
...
»

Summary of Contents for SINUMERIK 808D























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SINUMERIK 808D

Brand: KanexPro Pages: 12

Brand: ScatterBox Pages: 2

Brand: Hubbell Pages: 2

Brand: RFDesign Pages: 13

Brand: Danfoss Pages: 9

Brand: GLI Pages: 4

Blackbird HDBaseT 31058

Brand: Monoprice Pages: 16

Brand: RFS Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

CAN-T-Connector

Brand: ESD Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands