Siemens SINUMERIK 808D Diagnostic Manual Download Page 557

Page: 557 / 566

Loading system data in separate files (OEM or Siemens access level)

Select the desired operating area.

Press this softkey to open the system data window.

Press a softkey according to the backup path of the file.

Find the backed up file and press this softkey.

Press this softkey to open the 808D data window.

Paste the copies file to the corresponding folder with this softkey.

8.2.3

External data backup through the Ethernet interface

You can back up the system data files to your PC by means of a connected network drive. The

network drive functions based on the Ethernet connection between the control system and a

PC.

Creating and connecting a network drive

Prerequisite: A network connection has been established between the control system and the

PC. For more information about establishing Ethernet connections, see section "Configuring

the Ethernet connection (Page 41)".
Proceed as follows to create and connect a network drive:

Share a directory on your local disk on your PC.

Select the desired operating area on the PPU.

Data backup

8.2 External data backup

Diagnostics Manual

Diagnostics Manual, 06/2015, 6FC5398-6DP10-0BA2

557

Summary of Contents for SINUMERIK 808D























































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SINUMERIK 808D

Reviews:

Related manuals for SINUMERIK 808D

Brands by name

Popular brands

Siemens SINUMERIK 808D, Diagnostic Manual

Search results

Summary of Contents for SINUMERIK 808D

Reviews:

Related manuals for SINUMERIK 808D

Brands by name

Popular brands