Siemens SINUMERIK 808D Diagnostic Manual Download Page 334 | Manualshive

Page: 334 / 566

background image

Explanation:

It is impermissible to start a spindle as long as it is being used by a transformation. Reason: spindle usage in a

transformation requires axis operation, which must not be exited.
This alarm may have the following reasons:
- Error code 1 : M3, M4 or M5 per synchronized action;
- Error code 2 : M41 through M45 per synchronized action;
- Error code 3 : SPOS, M19 per synchronized action;
- Error code 11 : DB380x DBX5006.0 (Spindle stop);
- Error code 12 : DB380x DBX5006.1 (Spindle start clockwise rotation);
- Error code 13 : DB380x DBX5006.2 (Spindle start counterclockwise rotation;
- Error code 14 : DB380x DBX5006.4 (Spindle positioning).

Reaction:

NC Start disable in this channel.
Interface signals are set.
Alarm display.

Remedy:

Resolve the conflict, for example by deactivating transformation prior to spindle start.

Programm

continuation:

Clear alarm with the Delete key or NC START.

22292

[Channel %1: ] Changeover of the operating mode of the axis/spindle %2 using PI service not

possible, Cause %3

Parameters:

%1 = Channel number
%2 = Axis/spindle
%3 = Cause

Explanation:

It is not possible to change over the operating mode of the axis/spindle.
Cause:
1: The required axis/spindle is not known in the channel.
2: The required axis/spindle is not available in the channel.
3: The required axis/spindle is defined as virtual axis.
4: The required axis is not defined as spindle. Therefore, it is not possible to change over the operating mode of the axis.
5: The required axis/spindle is a permanently assigned PLC axis/spindle.
6: The required axis/spindle is an active slave axis/spindle.
7: Spindle operation is not possible for transformed spindle/axis.
8: The required axis/spindle is not available as command axis.

Reaction:

Alarm display.

Remedy:

1: Please select the PI service again.
2: Please select the PI service again.
3: Reset MD 30132 IS_VIRTUAL_AX.
4: When required, configure axis as spindle.
5: Axis/spindle enabled by the PLC.
6: Deactivate coupling of the slave axis/spindle.
7: Deactivate transformation.
8: Wait until the axis is again available.

Programm

continuation:

Clear alarm with the Delete key or NC START.

22295

[Channel %1: ] Spindle %2 DBB30 function not possible (cause: error code %3)

Parameters:

%1 = Channel number
%2 = Axis name, spindle number
%3 = Error code

SINUMERIK 808D ADVANCED alarms
5.2 NCK alarms

Diagnostics Manual

334

Diagnostics Manual, 06/2015, 6FC5398-6DP10-0BA2

«
...
332
333
334
335
336
...
»

Summary of Contents for SINUMERIK 808D























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SINUMERIK 808D

Brand: E+E Elektronik Pages: 2

Brand: FasTest Pages: 3

WattsRediant RadiantPEX-AL

Brand: Watts Pages: 2

Brand: cable matters Pages: 8

Brand: Eagle Pages: 2

1386CAN-PILL-00

Brand: Assa Abloy Pages: 36

Brand: ANTIFERENCE Pages: 7

Brand: Staubli Pages: 20

Brand: NewStar Pages: 4

Brand: Lenze Pages: 6

Brand: TRENDnet Pages: 10

GTV-HDMI1.3-144

Brand: Gefen Pages: 10

Brand: Warmup Pages: 3

Brand: Rittal Pages: 12

Brand: Kinivo Pages: 10

Brand: Connect Research Pages: 2

LM-SP144E-HD4K2K

Brand: LINK-MI Pages: 3

Brand: Monoprice Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands