Siemens SINUMERIK 808D Diagnostic Manual Download Page 310

Page: 310 / 566

20083

[Channel %1: ] Axis %2 programmed position %4 lies behind the coordinate system-specific

working area limit %3

Parameters:

%1 = Channel number
%2 = Axis number
%3 = "+" or "-"
%4 = End position

Explanation:

The axis is traversed as a reciprocating axis, and the target position (reversal position or end position) is located behind

the corresponding, valid, coordinate system-specific working area limitation. The axis is not traversed.

Reaction:

Local alarm reaction.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.

Remedy:

Specify smaller target position.
Deactivate working area limitation.
Set working area limitation differentially.

Programm

continuation:

Clear alarm with the RESET key. Restart part program

20085

[Channel %1: ] Contour handwheel: traverse direction or overtravel of beginning of block not

allowed

Parameters:

%1 = Channel number

Explanation:

Travel takes place on the path with the contour handwheel in the opposite direction to the programmed travel direction

and the starting point of the path has been reached at the start of the block.

Reaction:

Alarm display.

Remedy:

Turn the contour handwheel in the opposite direction.

Programm

continuation:

Alarm display showing cause of alarm disappears. No further operator action necessary.

20120

Axis %1: too many compensation relations

Parameters:

%1 = Axis name, spindle number

Explanation:

Interpolatory compensation with tables. For each axis, the maximum number of compensation relationships defined may

be no more than the number of axes in the system. In this alarm, the interpolatory compensation in the axis is switched

off automatically.

Reaction:

Interface signals are set.
Alarm display.

Remedy:

Check table parameters $AN_CEC_OUTPUT_AXIS and correct and/or switch off one or more tables (SD41300

$SN_CEC_TABLE_ENABLE).

Programm

continuation:

Clear alarm with the RESET key. Restart part program

20121

Axis %1: Configuration error in compensation table %2

Parameters:

%1 = Axis name, spindle number
%2 = Compensation table

Explanation:

Interpolatory compensation with tables. The settings for the specified table are not allowed. $AN_CEC_MAX >=

$AN_CEC_MIN and $AN_CEC_STEP != 0 apply to system variables. This table is switched off automatically.

Reaction:

Interface signals are set.
Alarm display.

Remedy:

Please inform the authorized personnel/service department. Check and correct the characteristic data in the compensation

table. If the error cannot be found, the alarm can be suppressed by switching off the table ($SN_CEC_TABLE_ENABLE)

or switching off compensation in the axis ($MA_CEC_ENABLE).

SINUMERIK 808D ADVANCED alarms
5.2 NCK alarms

Diagnostics Manual

310

Diagnostics Manual, 06/2015, 6FC5398-6DP10-0BA2

Summary of Contents for SINUMERIK 808D























































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SINUMERIK 808D

Reviews:

Brands by name

Popular brands

Siemens SINUMERIK 808D, Diagnostic Manual

Search results

Summary of Contents for SINUMERIK 808D

Reviews:

Brands by name

Popular brands