manualshive.com logo in svg

Oracle X5-4, Service Manual

The Oracle X5-4 is a powerful and versatile server, designed for high-performance computing. To get acquainted with its features and functionalities, make sure to download the free "Getting Started Manual" from our website. This comprehensive manual will provide you with all the necessary information to maximize your experience with the Oracle X5-4.

Share
Download
background image

Server Subsystems Overview

reset might be required after a software or firmware update or when you want to launch Oracle

System Assistant or the BIOS Setup Utility.

Cold Reset

 

A cold reset occurs when you restart the server from a completely powered-off state. A cold

reset might be required to resolve a system issue. To perform a cold reset, place the server in

standby power mode, disconnect the server from its AC power source, wait 30-60 seconds, then

reconnect the server to its AC power source, allow the SP to boot, and then reapply full power.

See Also:

■

“Power On the Server” on page 271

■

“Powering Off the server” on page 101

.

■

“Resetting the Host or Service Processor” on page 63

.

Storage Subsystem

The server storage subsystem consists of the following:

■

“Six 2.5-inch Drive Bays” on page 30

■

“SATA DVD +/-RW Drive” on page 31

Six 2.5-inch Drive Bays

The six 2.5-inch storage drive bays are located at the front of the server. The supported drive

interfaces for each bay depend on the type of storage controller installed at the factory. SAS

drives require a SAS Host Bus Adapter (HBA) and NVMe drives require a PCIe NVMe Switch

card.

30

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Related manuals for X5-4

D-Link DP-300+ User Manual preview
DP-300+
Brand: D-Link Pages: 38
D-Link Epress EtherNetwork DP-301P+ Datasheet preview
Epress EtherNetwork DP-301P+
Brand: D-Link Pages: 2
Hanwha WRR-5301 Replacement Manual preview
WRR-5301
Brand: Hanwha Pages: 3
IBM eserver xSeries 306 Option Installation Manual preview
eserver xSeries 306
Brand: IBM Pages: 46
Supero SUPERSERVER 6027R-TRF User Manual preview
SUPERSERVER 6027R-TRF
Brand: Supero Pages: 102
Polycom KIRK 14117800 Installation And Configuration Manual preview
KIRK 14117800
Brand: Polycom Pages: 220
xFusion Digital Technologies FusionServer G5500 V6 Manual preview
FusionServer G5500 V6
Brand: xFusion Digital Technologies Pages: 100
TerraMaster NAS U8-111 Quick Start Manual preview
NAS U8-111
Brand: TerraMaster Pages: 13
Silex technology PRICOM PRICOM C- 5100 User Manual preview
PRICOM PRICOM C- 5100
Brand: Silex technology Pages: 7
IBM 8678 Installation And User Manual preview
8678
Brand: IBM Pages: 96
IEI Technology PUZZLE-IN004 Series User Manual preview
PUZZLE-IN004 Series
Brand: IEI Technology Pages: 102
HPE ProLiant DL380 Gen9 Product End-Of-Life Disassembly Instructions preview
ProLiant DL380 Gen9
Brand: HPE Pages: 8
CNET CNP-101U Hardware User'S Manual preview
CNP-101U
Brand: CNET Pages: 14
Compaq AlphaServer GS60E Quick Specification preview
AlphaServer GS60E
Brand: Compaq Pages: 16
Compaq AlphaServer DS20E Technical Manual preview
AlphaServer DS20E
Brand: Compaq Pages: 16
Compaq ProLiant 4500 Servers Maintenance And Service Manual preview
ProLiant 4500 Servers
Brand: Compaq Pages: 89
Compaq AlphaServer GS60E Service Manual preview
AlphaServer GS60E
Brand: Compaq Pages: 180
Oce Repro Desk User Manual preview
Repro Desk
Brand: Oce Pages: 464

Brands by name

Popular brands

Load more brands