manualshive.com logo in svg

Oracle X5-4, Service Manual

The Oracle X5-4 is a powerful and versatile server, designed for high-performance computing. To get acquainted with its features and functionalities, make sure to download the free "Getting Started Manual" from our website. This comprehensive manual will provide you with all the necessary information to maximize your experience with the Oracle X5-4.

Share
Download
background image

Component Serviceability, Locations, and Designations

Component Serviceability

The replaceable components in your server are designated as either a customer-replaceable unit

(CRU) or a field-replaceable unit (FRU).

■

A part designated as a FRU must be replaced by an Oracle-qualified service technician.

■

A part designated as a CRU can be replaced by a person who is not an Oracle-qualified

service technician.

If the component can be serviced while the server is powered on, it is called a hot-service

component. If the server has to be powered off before the component can be serviced, it is

called a cold-service component.

The following table lists the components, their service designations, and their serviceability.

Component

Service Designation

Serviceability

Storage drives

CRU

Hot

Fan modules

CRU

Hot

Power supplies

CRU

Hot

Memory risers and DIMMs

CRU

Cold

PCIe cards

CRU

Cold

DVD drive

CRU

Cold

System (or RTC) battery

CRU

Cold

CPUs and heatsinks

FRU

Cold

SAS 12 Gb/s HBA and cables (HBA-to-disk backplane)

FRU

Cold

PCIe NVMe Switch card and cables (card-to-disk backplane)

FRU

Cold

Energy Storage Module (ESM) and cable (HBA-to-ESM)

FRU

Cold

Fan board

FRU

Cold

Power supply backplane

FRU

Cold

Storage drive backplane

FRU

Cold

SP card

FRU

Cold

Motherboard

FRU

Cold

Location of Replaceable Components

The following illustrations show the Oracle Server X5-4 components:

70

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Related manuals for X5-4

IBM BladeCenter HS22 Product Manual preview
BladeCenter HS22
Brand: IBM Pages: 18
Xerox EX Printing Manual preview
EX
Brand: Xerox Pages: 40
Radware APSolute Vision Installation And Maintenance Manual preview
APSolute Vision
Brand: Radware Pages: 81
TRENDnet TEW-MP1U (French) Manual D'Installation Rapide preview
TEW-MP1U
Brand: TRENDnet Pages: 14
7thSense M101-4 User Manual preview
M101-4
Brand: 7thSense Pages: 28
Protogate Freeway 3112 Hardware Installation Manual preview
Freeway 3112
Brand: Protogate Pages: 30
XtendLan IVS400A User Manual preview
IVS400A
Brand: XtendLan Pages: 28
RoviSys OPC90 User Manual preview
OPC90
Brand: RoviSys Pages: 146
VisionxIP VxIP 7111 User Manual preview
VxIP 7111
Brand: VisionxIP Pages: 77
Meinberg LANTIME M300/MGR Manual preview
LANTIME M300/MGR
Brand: Meinberg Pages: 5
Red Hat DIRECTORY SERVER 7.1 SP7 - S Release Note preview
DIRECTORY SERVER 7.1 SP7 - S
Brand: Red Hat Pages: 12
C-MOR IP Video Surveillance User Manual preview
IP Video Surveillance
Brand: C-MOR Pages: 62
Mozaex ShowStar User Manual preview
ShowStar
Brand: Mozaex Pages: 66
Supero AS 1021TM-INF+ User Manual preview
AS 1021TM-INF+
Brand: Supero Pages: 90
Supero A+ SERVER 2022G-URF User Manual preview
A+ SERVER 2022G-URF
Brand: Supero Pages: 94
Supero A+ SERVER User Manual preview
A+ SERVER
Brand: Supero Pages: 94
Supero A+ SERVER 2042G-6RF User Manual preview
A+ SERVER 2042G-6RF
Brand: Supero Pages: 114
Supero 6027R-3RF4 User Manual preview
6027R-3RF4
Brand: Supero Pages: 106

Brands by name

Popular brands

Load more brands