manualshive.com logo in svg

Oracle X5-4, Service Manual

Share
Download
Oracle X5-4 Service Manual Download Page 122

Prepare an NVMe Storage Drive for Removal

■

For a list of the virtual PCIe slots of NVMe drives as seen by the operating system, see

“NVMe Storage Drive Virtual PCIe Slot Designation” on page 115

. Note that the virtual

PCIe slot name is not the same as the name on the server front panel label.

1.

Log in to the Oracle Solaris host.

2.

Find the NVMe drive virtual PCIe slot number. Type:

# 

hotplug list –lc

This command produces output similar to the following for each of the NVMe drives installed

in the server:

# hotplug list -lc
Connection           State           Description
Path                          
-------------------------------------------------------
pcie100              ENABLED         PCIe-Native
/pci@0,0/pci8086,2f06@2,2/pci111d,80b5@0/pci111d,80b5@4
pcie101              ENABLED         PCIe-Native
/pci@0,0/pci8086,2f06@2,2/pci111d,80b5@0/pci111d,80b5@5
pcie102              ENABLED         PCIe-Native
/pci@0,0/pci8086,2f06@2,2/pci111d,80b5@0/pci111d,80b5@6
pcie103              ENABLED         PCIe-Native
/pci@0,0/pci8086,2f06@2,2/pci111d,80b5@0/pci111d,80b5@7

3.

Prepare the NVMe drive for removal by powering off the drive slot.

For example, to prepare NVMe0 for removal, type the following commands:
# 

hotplug poweroff pcie100

# 

hotplug list –lc

The following output appears for the NVMe0 drive that has been unmounted:

# hotplug list -lc
Connection           State           Description
Path                          
-------------------------------------------------------
pcie100              PRESENT         PCIe-Native
/pci@0,0/pci8086,2f06@2,2/pci111d,80b5@0/pci111d,80b5@4
pcie101              ENABLED         PCIe-Native
/pci@0,0/pci8086,2f06@2,2/pci111d,80b5@0/pci111d,80b5@5
pcie102              ENABLED         PCIe-Native
/pci@0,0/pci8086,2f06@2,2/pci111d,80b5@0/pci111d,80b5@6
pcie103              ENABLED         PCIe-Native
/pci@0,0/pci8086,2f06@2,2/pci111d,80b5@0/pci111d,80b5@7

4.

Verify that the blue OK to Remove indicator on the NVMe drive is lit.

122

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands