manualshive.com logo in svg

Oracle X5-4, Service Manual

Share
Download
Oracle X5-4 Service Manual Download Page 200

Servicing the Factory Installed SAS 12 Gb/s Internal HBA and ESM

Servicing the Factory Installed SAS 12 Gb/s Internal HBA

and ESM

This section provides procedures for removing and installing the factory-installed SAS HBA

card and ESM.

For information about the factory installed SAS 12 Gbit/sec HBA, see 

“Storage

Subsystem” on page 30

. For serviceability information, see 

“Component Serviceability,

Locations, and Designations” on page 69

.

■

“Replace the SAS 12 Gb/s Internal HBA (FRU)” on page 200

■

“Replace the SAS 12 Gb/s Internal HBA ESM Module (FRU)” on page 203

■

“Replace the SAS 12 Gb/s Internal HBA SAS Cables (FRU)” on page 204

■

“Replace the SAS 12 Gb/s Internal HBA ESM Cable (FRU)” on page 209

Replace the SAS 12 Gb/s Internal HBA (FRU)

When servicing the components in this section, unplug the AC power cords and use ESD

protection.

Before You Begin

If the HBA being replaced is already configured with RAID, and its configurations have

been saved to a RAID configuration file, be sure to have that file on hand to restore to the

replacement HBA card. Refer to the HBA documentation for details.

1.

Prepare the server for service.

See 

“Prepare the Server for Cold Service” on page 94

.

2.

Remove the HBA card from PCIe slot 2 slot and disconnect cables attached to it.

200

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands