manualshive.com logo in svg

Oracle X5-4, Service Manual

Share
Download
Oracle X5-4 Service Manual Download Page 202

Replace the SAS 12 Gb/s Internal HBA (FRU)

For details on installing a card, see 

“Install a PCIe Card” on page 164

.

4.

Prepare the server for operation.

See 

“Prepare the Server for Operation” on page 259

.

5.

Restore configurations from the old card to the replacement card.

If you are replacing an HBA that was already configured for RAID, obtain the saved

configuration file to restore to the replacement HBA card.
For details on configuring or recovering RAID configurations, refer to the Avago Technologies

LSI Storage 

12Gb/s MegaRAID SAS Software User's Guide

, which is available at the following

location: 

http://www.lsi.com/sep/Pages/oracle/index.aspx

202

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands