Oracle X5-4 Service Manual Download Page 119

Page: 119 / 358

Install a Storage Drive Filler Panel (CRU)

Close the latch to lock the drive in place.

Do one of the following:

■

If you have replaced an NVMe drive using a hot-service procedure, refer to

the following for powering on the device:

■

“Removing and Replacing an NVMe Storage Drive Using Oracle

Solaris” on page 121

■

“Removing and Replacing an NVMe Storage Drive Using Oracle

Linux” on page 125

■

If you have replaced a storage drive using a cold-service procedure, power

on the server and configure the storage drive.

Use one of the power options described in

“Power On the Server” on page 271

Perform administrative tasks to reconfigure the drive.

The procedures that you perform at this point depend on how your data is configured. You

might need to partition the drive, create file systems, load data from backups, or have the drive

updated from a RAID configuration.

See Also

■

“Storage Drive Reference” on page 119

Install a Storage Drive Filler Panel (CRU)

For information about component filler panels, see

“Component Filler Panels” on page 81

Verify that the release lever on the storage drive filler panel is fully opened.

To open the lever, push the release button on the front of the filler panel.

Slide the storage drive filler panel into the drive slot until it is fully seated.

Close the latch to lock the filler panel in place.

See Also

■

“Storage Drive Reference” on page 119

Storage Drive Reference

This section shows the location and explains the functions of the storage drive status indicators.

Servicing CRU Components

119

Summary of Contents for X5-4







































































































































































































































































































































































Search results

Summary of Contents for X5-4

Reviews:

Related manuals for X5-4

Brands by name

Popular brands

Oracle X5-4, Service Manual

Search results

Summary of Contents for X5-4

Reviews:

Related manuals for X5-4

Brands by name

Popular brands