manualshive.com logo in svg

Oracle X5-4, Service Manual

Share
Download
Oracle X5-4 Service Manual Download Page 239

Replace the Disk Drive Backplane (FRU)

You need to move the air divider so you can access the disk drive backplane board. The divider

is mounted to the power supply side wall using two tabs that are inserted into slots in the side

wall.

a.   

Lift the air divider so the tabs clear the slots in the power supply side wall.

b.   

Move the air divider away from the side wall and gently rotate the divider

and the cables attached to it away from the backplane area and set it on top

of installed memory risers.

7.

Disconnect the ribbon data cable and the power cable at the bottom of the disk

backplane board.

See the illustration shown in step 8.

8.

To release the spring-loaded lever [1], lift it upward [2].

The disk drive backplane sets on metal flanges and is secured by a spring-loaded lever.

9.

To remove the disk drive backplane, lift it, so it clears the support flanges, and

remove it from the server.

Servicing FRU Components

239

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands