manualshive.com logo in svg

Oracle X5-4, Service Manual

The Oracle X5-4 is a powerful and versatile server, designed for high-performance computing. To get acquainted with its features and functionalities, make sure to download the free "Getting Started Manual" from our website. This comprehensive manual will provide you with all the necessary information to maximize your experience with the Oracle X5-4.

Share
Download
background image

Servicing the DVD Drive (CRU)

Note - 

If the system was ordered from the factory with optional NVMe drives, a PCIe NVMe

Switch card is installed in PCIe slot 1.

As a general rule, when installing a PCIe card in the server, use the following population order:

■

For a two-CPU configuration, the slot population order is: slot 6, 4, 5, 3, 1.
For example: When installing a PCIe card in a two-CPU configured server, first, determine

if slot 6 is available. If it is available, install the card in the slot. If it is not available,

determine if slot 4 is available. If slot 4 is not available, determine if slot 5 is available.

Continue this process with slots 3, and 1 until you find an available slot.

■

For a four-CPU configuration, the slot population order is: slot 11, 8, 6, 4, 10, 7, 5, 3, 9, 1
For example, when installing a PCIe card in a four-CPU configured server, first determine

if slot 11 is available. If it is available, install the card in the slot. If it is not available,

determine if slot 8 is available. If slot 8 is not available, determine if slot 6 is available.

Continue this process with slots 4, 10, 7, 5, 3, 9, and 1 until you find an available slot.

PCIe Cards With Boot Devices

If the server has several PCIe cards that provide boot devices, disable the Option ROM on the

PCIe slots not used for booting. By default, the BIOS enables Option ROMs for PCIe slot 2 and

the four on-board 10 Gigabit Ethernet ports.

Servicing the DVD Drive (CRU)

This section provides procedures for removing and installing the DVD drive and filler panel.

■

“Remove the DVD Drive or DVD Drive Filler Panel” on page 168

■

“Install the DVD Drive or DVD Drive Filler Panel” on page 170

Remove the DVD Drive or DVD Drive Filler Panel

When servicing the components in this section, unplug the AC power cords and use ESD

protection.

168

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Related manuals for X5-4

IBM BladeCenter HS23 Product Manual preview
BladeCenter HS23
Brand: IBM Pages: 28
NEC Univerge SV9300 Programming Manual preview
Univerge SV9300
Brand: NEC Pages: 47
NEC Univerge SV9100 Manual preview
Univerge SV9100
Brand: NEC Pages: 766
Omneon MediaDeck Installation Manual preview
MediaDeck
Brand: Omneon Pages: 2
QNAP TS-130-US User Manual preview
TS-130-US
Brand: QNAP Pages: 39
sysmik ICS-709 Installation Notes For Electrical Personnel preview
ICS-709
Brand: sysmik Pages: 2
IBM eserver xSeries 306 Option Installation Manual preview
eserver xSeries 306
Brand: IBM Pages: 46
Newtec NOP1840 PEP-Box User Manual preview
NOP1840 PEP-Box
Brand: Newtec Pages: 96
Velleman VWS2E Manual preview
VWS2E
Brand: Velleman Pages: 17
HPE ProLiant ML110 Gen 10 Product End-Of-Life Disassembly Instructions preview
ProLiant ML110 Gen 10
Brand: HPE Pages: 5
IBM eServer xSeries 205 Type 8480 Hardware Maintenance Manual And Troubleshooting Manual preview
eServer xSeries 205 Type 8480
Brand: IBM Pages: 168
Fujitsu PRIMEQUEST 440 System Design Manual preview
PRIMEQUEST 440
Brand: Fujitsu Pages: 280
Brother NC-100h Network User'S Manual preview
NC-100h
Brand: Brother Pages: 103
Dell EMC VxFlex Appliance R840 Owner'S Manual preview
EMC VxFlex Appliance R840
Brand: Dell Pages: 44
Dell EqualLogic PS4000 Configuration Manual preview
EqualLogic PS4000
Brand: Dell Pages: 73
Dell EMC PowerProtect DD6400 System Expansion Manuallines preview
EMC PowerProtect DD6400 System
Brand: Dell Pages: 46
Dell EqualLogic PS5500 Maintenance Manual preview
EqualLogic PS5500
Brand: Dell Pages: 8
Dell FC4700 Setup Manual preview
FC4700
Brand: Dell Pages: 22

Brands by name

Popular brands

Load more brands